Parameters
SMCS - 7601-NQ ; 7603-NQ
Note: This table is an expanded listing to cover a larger population of machines. Some components listed in the table may not apply to your machine.
Table 1
VIMS Parameter Description List |
|||||
Parameter Number |
VIMS Abbreviated Name |
VIMS Full Name |
Source Module(s) |
Signal Type |
Parameter Description |
99 |
THROTTL LCK ENABL |
Throttle Lock Enable Switch |
36 |
Calculated |
“Indicates the position (ON or OFF) of the throttle lock enable switch.” |
100 |
ENG SPD |
Engine Speed |
36 |
Frequency |
“The actual rotational speed of the crankshaft. The sensor is mounted on the flywheel housing (994) or on the camshaft (engine ECM). The sensor generates a frequency-varying signal as the teeth on the gear pass. The frequency-varying signal is sent to an ECM. The ECM uses the frequency-varying signal in order to determine the speed of the engine.” |
101 |
TRBO IN PRES |
Turbo Inlet Pressure |
36 |
Analog |
“The turbocharger inlet air pressure sensor sends the engine ECM a voltage that varies as the pressure changes. The engine ECM then calculates the pressure according to the voltage that is received.” |
102 |
LT TRBO IN PRES |
Left Turbocharger Inlet Pressure |
36 |
Analog |
“The left bank turbocharger inlet pressure sensor sends the engine ECM a voltage that varies as the pressure changes. The engine ECM then calculates the pressure according to the voltage that is received.” |
103 |
RT TRBO IN PRES |
Right Turbo Inlet Pressure |
36 |
Analog |
“The right bank turbocharger inlet pressure sensor sends the engine ECM a voltage that varies as the pressure changes. The engine ECM then calculates the pressure according to the voltage that is received.” |
104 |
PEAK AIR FLTR |
Peak Air Filter (Restriction) |
36 |
Calculated |
“This is used to show the peak or maximum air filter restriction for a given period of time. The engine ECM calculates the value by subtracting the atmospheric pressure value from the turbo inlet pressure value.” |
104 |
AIR FLTR |
Air Filter (Restriction) |
36 |
Calculated |
“Indicates the degree to which the engine air filter is plugged. The engine ECM uses the parameters of atmospheric air pressure and turbocharger inlet air pressure to calculates the degree to which the engine air filter is plugged. Engine power is derated 2 percent per kpa of pressure difference above 6.5 kpa, up to a maximum of 20 percent total engine derate. If the engine ECM senses that either one of these pressure sensors are sending an incorrect value, the engine power is also derated up to 20 percent.” |
105 |
BOOST PRES |
Boost Pressure |
36 |
Analog |
“The turbocharger outlet pressure sensor sends the engine ECM a voltage that varies as the pressure changes. The engine ECM then calculates boost according to the voltage that is received by subtracting atmospheric pressure. ” |
106 |
LT EXH TEMP |
Left Exhaust Temperature |
36 |
PWM |
“The temperature within the left bank exhaust manifold of the engine. An ECM receives a signal that changes in pulse width as the exhaust within the left exhaust manifold changes temperature. The ECM uses the pulse width that it receives in order to determine the temperature.” |
107 |
RT-LT EXH TEMP |
Right Minus Left Exhaust Temperature |
49 |
Calculated |
“This is calculated by VIMS by subtracting the left manifold exhaust temperature from the right manifold exhaust temperature.” |
108 |
RT EXH TEMP |
Right Exhaust Temperature |
36 |
PWM |
“The temperature within the right exhaust manifold of the engine. An ECM receives a signal that changes in pulse width as the exhaust within the right exhaust manifold changes temperature. The ECM then uses the pulse width that it receives to determine the temperature.” |
109 |
TRBO OUT PRES |
Turbo Outlet Pressure |
36 |
Analog |
“The turbocharger outlet pressure sensor sends the engine ECM a voltage that changes as the pressure changes. The engine ECM then calculates the pressure according to the voltage received.” |
110 |
AFTCLR TEMP |
Aftercooler Temperature (Coolant) |
36/49 |
PWM |
“Engine aftercooler coolant outlet temperature. An ECM receives a signal that changes in pulse width as the engine aftercooler coolant outlet temperature changes. The ECM then uses the pulse width that it receives to determine the temperature.” |
111 |
F AFTRCLR TEMP |
Front Aftercooler Temperature (Coolant) |
36/49 |
PWM |
“The temperature in the front section of the engine aftercooler. An ECM receives a signal that changes in pulse width as the coolant in the front section of the engine aftercooler changes temperature. The ECM uses the pulse width that it receives to determine the temperature.” |
112 |
R AFTRCLR TEMP |
Rear Aftercooler Temperature (Coolant) |
36/49 |
PWM or Analog |
“The temperature in the rear section of the engine aftercooler. An ECM receives a signal that changes in pulse width as the coolant in the rear section of the engine aftercooler changes temperature. The ECM uses the pulse width that it receives to determine the temperature. ” |
113 |
START AID SW |
Start Aid Switch |
36 |
Switch |
“Indicates the status of the start aid function (ON or OFF).” |
114 |
WASTEGATE POS |
Wastegate Position |
36 |
Analog |
“The position of the wastegate valve on the turbocharger (outlet). The wastegate position sensor has an output that changes in voltage as the wastegate valve position changes. From this voltage, the engine ECM calculates the wastegate position.” |
115 |
COOL FAN SPD |
Cooling Fan Speed |
36 |
Frequency |
“The speed of the engine cooling fan shaft. The sensor mounted on this shaft generates a frequency varying signal that changes as the speed of the cooling fan changes. From this signal, the engine ECM calculates the engine cooling fan speed.” |
116 |
ENG COLD MODE |
Cold Mode Status |
36 |
Calculated |
“Indicates the cold mode status (active or inactive) as calculated by the engine ECM.” |
117 |
ENG DERATE |
Engine Power Derate Percentage |
36 |
Calculated |
“Used to request and read the present engine power derate percentage. Zero indicates engine power is NOT derated.” |
118 |
AIR FLTR |
Peak Air Filter Restriction |
36 |
Calculated |
“Indicates the peak air filter restriction as calculated by the engine ECM.” |
119 |
ETHER INJEC |
Ether Injection |
36 |
Calculated |
“Indicates when ether is being injected into an engine to aid starting.” |
120 |
FUEL POS |
Fuel Position |
36 |
Calculated |
“This is calculated by the engine ECM after considering the desired engine speed, fuel ratio control (FRC), and actual engine speed.” |
121 |
ENG LOAD |
Engine Load |
36 |
Calculated |
“This is calculated by the engine ECM after considering the engine speed, throttle switch position, throttle position, boost pressure, and atmospheric pressure and is shown as a percent of a full load.” |
122 |
FUEL FLTR |
Fuel Filter (Bypass) |
36/49 |
Switch |
“The status of the fuel filter (PLUGGED or OK). When the pressure across the filter is greater than the specified pressure, the switch plunger moves and allows the switch contacts to open telling an ECM that the filter is PLUGGED. With normal operation, the switch is closed to ground.” |
123 |
FUEL LVL |
Tank Fuel Level |
49 |
PWM |
“This is the tank fuel level and is measured by the ultrasonic fuel level sensor that is mounted in the bottom of the fuel tank. This sensor sends an ECM a pulse that varies in width as the fuel level changes. The fuel level is then calculated according to the pulse width that it receives. The sensor also takes the temperature of the fuel into consideration, and changes the pulse width accordingly. ” |
125 |
THROTTL POS |
Throttle Position |
36 |
PWM |
“The position of the throttle foot pedal. The throttle position sensor has a pulse output that changes in width as the foot pedal position changes. The engine ECM uses the pulse width that it receives to determine the throttle position.” |
126 |
FUEL FLOW |
Fuel Flow |
36 |
Calculated |
“This is calculated by VIMS from the Fuel Flow Engl parameter received from the engine ECM. The Fuel Flow Engl value (parameter 127, in gal/sec), is converted to this fuel flow (parameter 126). This represents the rate at which fuel is used by the engine. The units for this parameter are gallons per hour.” |
127 |
FUEL FLOW ENGL |
Fuel Flow (English Units) |
36 |
Calculated |
“This is calculated by the engine ECM. It is used to show the rate at which fuel is used by the engine (English units). It is used on older machines. The units are gallons per second.” |
128 |
FUEL PRES |
Fuel Pressure Filtered (Primary) |
49 |
PWM |
“The fuel pressure after the fuel filter.” |
129 |
ENG FUEL RATE |
Engine Fuel Rate |
36 |
Calculated |
“This is calculated by the engine ECM, and is the rate at which fuel is used by the engine. The units are liters per hour.” |
130 |
ENG OIL LVL |
Engine Oil Level |
36/49 |
Switch |
“Used to tell the engine ECM when the engine oil level is less than the minimum desired level. With low oil level, the switch is open. In normal operation, the switch is closed to ground.” |
131 |
ENG OIL PRES |
Engine Oil Pressure |
36/49 |
Analog |
“The oil pressure inside the engine. The sensor sends to an ECM a voltage that varies as the pressure changes. The ECM then calculates the pressure according to the voltage that it receives. Actual warning pressure depends upon the engine speed.” |
132 |
ENG OIL PRES AB |
Engine Oil Pressure (Absolute) |
36 |
Analog |
“The oil pressure (absolute) inside the engine. The sensor sends to an ECM a voltage that varies as the pressure changes. The ECM then calculates the pressure according to the voltage that it receives. Actual warning pressure depends upon the engine speed. Atmospheric pressure is taken into account for this calculation.” |
133 |
CNKCASE PRES |
Crankcase Pressure |
36 |
Analog |
“The pressure inside the crankcase. The sensor sends the engine ECM a voltage that varies as the pressure changes. The engine ECM then calculates the pressure according to the voltage that it receives.” |
134 |
ENG COOL FLOW |
Engine Coolant Flow |
49 |
Switch |
“This switch notifies VIMS of the coolant flow status in the engine cooling system (water jacket). During normal operation, the coolant flow switch is closed to ground. The switch opens when coolant flow is less than specified.” |
135 |
ENG COOL TEMP |
Engine Coolant Temperature |
36/49 |
PWM |
“The coolant temperature in the engine cooling system. An ECM receives a signal that changes in voltage or pulse width as the engine coolant temperature changes. The ECM then determines the temperature from the signal it receives.” |
136 |
HYD COOLR BLKR |
Hydraulic Cooler Blocker |
49 |
Switch |
“The state of the Hydraulic Oil Cooler Blocker function.” |
137 |
AFTRCLR LVL |
Aftercooler (Coolant) Level |
49 |
Switch |
“This switch notifies VIMS of the status of the aftercooler coolant level. The switch (sensor) opens when the coolant level is low. During normal operation the switch is closed to ground. This switch (sensor) is a capacitive type switch that is activated only by water or anti-freeze.” |
138 |
ENG COOL LVL |
Engine Coolant Level |
49 |
Switch |
“This switch notifies VIMS of the status of the engine coolant level. The switch (sensor) opens when the coolant level is low. During normal operation the switch is closed to ground. This switch (sensor) is a capacitive type switch that is activated only by water or anti-freeze.” |
140 |
SYS VOLTAGE |
System Voltage |
49 |
Calculated |
“The actual voltage that exists between machine battery positive and frame ground measured at the main module.” |
141 |
MAIN PILOT PRES |
Main Pilot Pressure |
49 |
PWM |
“The hydraulic systems main pilot pressure. This pilot pressure includes the swing, implement, and travel pilot pressures. An ECM receives a signal that varies in pulse width as the pressure changes.” |
142 |
IMPL PRES |
Implement Pilot Oil Pressure |
49 |
PWM |
“Indicates the pressure of the pilot oil for implements. An ECM receives a signal that varies in pulse width as the pressure changes.” |
144 |
UNFLTR OIL PRES |
Unfiltered Oil Pressure |
36 |
Analog |
“The absolute pressure (includes atmospheric pressure) of the engine oil before the engine oil filter. The engine ECM receives a voltage that changes as the pressure changes.” |
145 |
HI BOOST PRES |
Boost Pressure Front or Rear High |
49 |
Calculated |
“This parameter monitors the warning status parameter from the engine ECM to determine if the front or rear boost pressure is high.” |
146 |
LO BOOST PRES |
Boost Pressure Front or Rear Low |
49 |
Calculated |
“This parameter monitors the warning status parameter from the engine ECM to determine if the front or rear boost pressure is low.” |
147 |
CNKCASE PRES |
Crankcase Air Pressure (Gauge) |
36 |
PWM |
“The pressure of the air inside the crankcase.” |
149 |
COLD CYL CUTOUT |
Cold Cylinder Cutout |
36 |
Calculated |
“Used to read and program the Cold Cylinder Cutout Strategy status.” |
150 |
AVE CYL TEMP |
Engine Cylinder No. 1 Exhaust Temperature |
36 |
Analog |
“The temperature of engine cylinder No. 1 exhaust.” |
151 |
INJ-CYL 1 TEMP |
Engine Cylinder No. 1 Exhaust Temperature |
36 |
Analog |
“The temperature of engine cylinder No. 1 exhaust.” |
152 |
INJ-CYL 2 TEMP |
Engine Cylinder No. 2 Exhaust Temperature |
36 |
Analog |
“The temperature of engine cylinder No. 2 exhaust.” |
153 |
INJ-CYL 3 TEMP |
Engine Cylinder No. 3 Exhaust Temperature |
36 |
Analog |
“The temperature of engine cylinder No. 3 exhaust.” |
154 |
INJ-CYL 4 TEMP |
Engine Cylinder No. 4 Exhaust Temperature |
36 |
Analog |
“The temperature of engine cylinder No. 4 exhaust.” |
155 |
INJ-CYL 5 TEMP |
Engine Cylinder No. 5 Exhaust Temperature |
36 |
Analog |
“The temperature of engine cylinder No. 5 exhaust.” |
156 |
INJ-CYL 6 TEMP |
Engine Cylinder No. 6 Exhaust Temperature |
36 |
Analog |
“The temperature of engine cylinder No. 6 exhaust.” |
157 |
INJ-CYL 7 TEMP |
Engine Cylinder No. 7 Exhaust Temperature |
36 |
Analog |
“The temperature of engine cylinder No. 7 exhaust.” |
158 |
INJ-CYL 8 TEMP |
Engine Cylinder No. 8 Exhaust Temperature |
36 |
Analog |
“The temperature of engine cylinder No. 8 exhaust.” |
159 |
INJ-CYL 9 TEMP |
Engine Cylinder No. 9 Exhaust Temperature |
36 |
Analog |
“The temperature of engine cylinder No. 9 exhaust.” |
160 |
INJ-CYL 10 TEMP |
Engine Cylinder No. 10 Exhaust Temperature |
36 |
Analog |
“The temperature of engine cylinder No. 10 exhaust.” |
161 |
INJ-CYL 11 TEMP |
Engine Cylinder No. 11 Exhaust Temperature |
36 |
Analog |
“The temperature of engine cylinder No. 11 exhaust.” |
162 |
INJ-CYL 12 TEMP |
Engine Cylinder No. 12 Exhaust Temperature |
36 |
Analog |
“The temperature of engine cylinder No. 12 exhaust.” |
163 |
INJ-CYL 13 TEMP |
Engine Cylinder No. 13 Exhaust Temperature |
36 |
Analog |
“The temperature of engine cylinder No. 13 exhaust.” |
164 |
INJ-CYL 14 TEMP |
Engine Cylinder No. 14 Exhaust Temperature |
36 |
Analog |
“The temperature of engine cylinder No. 14 exhaust.” |
165 |
INJ-CYL 15 TEMP |
Engine Cylinder No. 15 Exhaust Temperature |
36 |
Analog |
“The temperature of engine cylinder No. 15 exhaust.” |
166 |
INJ-CYL 16 TEMP |
Engine Cylinder No. 16 Exhaust Temperature |
36 |
Analog |
“The temperature of engine cylinder No. 16 exhaust.” |
167 |
ENG PRELUBE |
Engine Pre-Lube Mode |
36 |
Calculated |
“Indicates which mode the engine pre-lube system is in. Engine pre-lube modes:” Pre-Lube is OFF Pre-Lube is ON Pre-Lube is DISABLED Pre-Lube is COMPLETED |
168 |
LT AIR FLTR RES |
Left Air Filter Restriction |
36 |
Calculated |
“The pressure drop across the left bank air filter is calculated by subtracting the left turbo inlet pressure from the atmospheric pressure.” |
169 |
RT AIR FLTR RES |
Right Air Filter Restriction |
36 |
Calculated |
“The pressure drop across the right bank air filter is calculated by subtracting the right turbo inlet pressure from the atmospheric pressure.” |
171 |
ENG OIL PRES ST |
Engine Oil Pressure Status |
36/34/33 |
Calculated |
“The status of the engine oil pressure (OK, LO or HI).” |
172 |
CRNK WO INJ ST |
Crank Without Injection Status |
36/34/33 |
Switch |
“Reads the crank without injection status (OFF or ON).” |
173 |
THROTTL SW1 ST |
Throttle Switch No. 1 Status |
36 |
Switch |
“Indicates the status of throttle switch No. 1. When the switch contacts are closed (grounded) the status is ON.” |
174 |
THROTTL SW2 ST |
Throttle Switch No. 2 Status |
36 |
Switch |
“Indicates the status of throttle switch No. 2. When the switch contacts are closed (grounded) the status is ON.” |
175 |
THROTTL SW3 ST |
Throttle Switch No. 3 Status |
36 |
Switch |
“Indicates the status of throttle switch No. 3. When the switch contacts are closed (grounded) the status is ON.” |
176 |
THROTTL SW4 ST |
Throttle Switch No. 4 Status |
36 |
Switch |
“Indicates the status of throttle switch No. 4. When the switch contacts are closed (grounded) the status is ON.” |
177 |
RT AIR FLTR |
Right Air Filter Restriction |
36 |
Switch |
“This is the pressure drop across the right bank air filter. An open switch means a plugged filter.” |
178 |
LT AIR FLTR |
Left Air Filter Restriction |
36 |
Switch |
“This is the pressure drop across the left bank air filter. An open switch means a plugged filter.” |
179 |
AIR FLTR STATUS |
Air Filter Restriction Status |
36 |
Switch |
“The status of the air filter (PLUGGED or OK). When the pressure across the filter is greater than the specified pressure, the switch plunger moves and allows the switch contacts to open telling the ECM that the filter is PLUGGED. With normal operation the switch is closed to ground.” |
180 |
ENG STATUS |
Overall Truck Engine Status. |
36 |
Calculated |
“Indicates the engine status. This parameter provides the status (enabled or disabled) of the following features:” Altitude Derate Cold Mode Cell Throttle Elevated Idle Engine Derate Engine Speed Cold Cylinder Cutout Low Fuel Pressure Emergency Stop Shutdown Fuel Injection High Hydraulic Oil Temperature High Coolant Temperature Low Oil Pressure |
181 |
ALTERNATOR #1 |
Alternator No.1 |
49 |
Frequency |
“The speed as indicated by the alternator R terminal signal. The R terminal signal is affected by belt slip and the alternator health.” |
182 |
ALTERNATOR #2 |
Alternator No.2 |
87 |
Frequency |
“The speed as indicated by the alternator R terminal signal. The R terminal signal is affected by belt slip and the alternator health.” |
184 |
THROTTL BYPASS |
Throttle Bypass |
36 |
Switch |
“The throttle override status. The status is either OFF or ON.” |
188 |
TURBO INLET TEMP |
Turbo Inlet Temperature |
36 |
Analog |
“The temperature of the turbo inlet air to the engine.” |
230 |
FNL LUBE PRES |
Final Drive Lube Low Pressure |
116 |
Switch |
“The status (OK, LOW or HIGH) of the final drive (differential) pump pressure, as indicated by a switch or sensor.” |
231 |
BVL DIFF FLTR |
Diferential (Bevel Gear) Filter Status |
116 |
Switch |
“The status (PLUGGED or OK) of the differential (bevel gear) filter as indicated by a switch or sensor.” |
232 |
BVL PMP PRES |
Differential (Bevel Gear) Lube Pressure |
116 |
PWM |
“The differential (bevel gear) lube pressure. The ECM reads the pulse width of the signal and determines the pressure from the signal that is received.” |
233 |
FNL LUBE FLTR |
Final Drive Filter Switch |
116 |
Switch |
“The position (PLUGGED or OK) of the final drive (differential) filter switch.” |
234 |
DIFF OIL LVL |
Differential Oil Level |
116 |
Switch |
“The position of the differential (drive axle) oil level switch.” |
235 |
DIFF TEMP |
Differential Oil Temperature |
116 |
PWM |
“The temperature of the oil in the differential (axle). The ECM reads the pulse width of the signal and determines the pressure from the signal that is received.” |
240 |
GND LVL SHUTDN R |
Ground Level Shutdown Signal Rear |
36 |
Switch |
“The status (ON or OFF) of the rear engine ground level shutdown switch.” |
242 |
ENG CPLNG PRESS |
Engine Coupling Oil Pressure |
36 |
Analog |
Coupling oil pressure status (LO or OK). |
250 |
GND LVL SHUTDN F |
Ground Level Shutdown Signal Front |
33 |
Switch |
“The status (ON or OFF) of the front engine ground level shutdown switch.” |
251 |
ENG DERATE F |
Engine Derate Percentage Front |
33 |
Analog |
“This indicates the present front engine power percentage. Zero indicates that the engine is not derated” |
252 |
GOV STATUS F |
Slave Governing Status Front Engine |
34 |
Calculated |
“Indicates the governing status (ALONE or SLAVE) of the front engine slave ECM.” |
253 |
F AFTRCLR TEMP |
Front Aftercooler Temperature (Coolant) |
33 |
PWM |
“The temperature of the coolant in the engine front aftercooler system. ON MACHINES WITH TWO ENGINE AFTERCOOLER COOLANT TEMPERATURE SENSORS THIS REFERS TO THE FRONT ENGINE AFTERCOOLER COOLANT TEMPERATURE.” |
254 |
AIR FLTR F |
Engine Peak Air Filter (Restriction) Front |
33 |
Calculated |
“Reads the peak air filter restriction of the front engine.” |
255 |
BOOST PRES F |
Engine Outlet (Boost) Pressure Front |
33 |
Analog |
“The pressure downstream on the compressor discharge side of the turbocharger on the front engine.” |
256 |
CNKCASE PRES F |
Engine Crankcase Pressure Front |
33 |
PWM |
“The pressure inside the crankcase of the front engine.” |
258 |
F ENG LOAD |
Engine Load Front |
33 |
Analog |
“The actual percentage of front engine load.” |
259 |
ENG OIL FLTR F |
Engine Oil Filter Differential Pressure (Gauge) Front |
33 |
PWM |
“The pressure drop across the engine oil filter for the front engine.” |
260 |
ENG OIL LVL F |
Engine Oil Level Front |
33 |
Switch |
“The level of the oil in the crankcase for the front engine.” |
261 |
ENG OIL PRES F |
Engine Oil Pressure Front |
33 |
Analog |
“The oil pressure inside the front engine. The sensor sends to an ECM a voltage that varies as the pressure changes. The ECM then calculates the pressure according to the voltage that it receives. Actual warning pressure depends upon the engine speed.” |
262 |
F ENG STATUS |
Engine Status Front |
33 |
Calculated |
“The front engine status. This parameter provides the status (enabled or disabled) of the following features: ” Altitude Derate Cold Mode Cell Throttle Elevated Idle Engine Derate Engine Speed Cold Cylinder Cutout Low Fuel Pressure Emergency Stop Shutdown Fuel Injection High Hydraulic Oil Temperature High Coolant Temperature Low Oil Pressure |
263 |
F WASTEGATE POS |
Front Wastegate Position |
33 |
Analog |
“The position of the wastegate valve on the front engine turbocharger (outlet). The wastegate position sensor has an output that changes in voltage as the wastegate valve position changes From this voltage the front eng ECM calculates the waste gate position.” |
264 |
F FUEL FLTR |
Engine Fuel Filter Status Front |
33 |
Switch |
“The status of the front engine fuel filter (PLUGGED or OK). When the pressure across the filter is greater than the specified pressure, the switch plunger moves and allows the switch contacts to open telling an ECM that the filter is PLUGGED. With normal operation, the switch is closed to ground.” |
265 |
BOOST PRES HI F |
High Boost Pressure Front |
49 |
Analog |
“The front turbocharger outlet pressure sensor sends the engine ECM a voltage that varies as the pressure changes. The engine ECM then calculates boost according to the voltage that is received by subtracting atmospheric pressure.” |
266 |
OIL PRES F LO |
Low Oil Pressure Front |
49 |
Switch |
“This parameter monitors the engine status parameter to see if the front engine oil pressure is low.” |
267 |
EXH TEMP LTF |
Engine Left Front Turbo Exhaust Temperature |
33 |
PWM |
“The temperature of the exhaust on the left bank of the front engine.” |
268 |
EXH TEMP RTF |
Engine Right Front Turbo Exhaust Temperature |
33 |
PWM |
“The temperature of the exhaust on the right bank of the front engine.” |
269 |
F RT- F LT EXH TEMP |
Front Right Minus Front Left Exhaust Temperature |
49 |
Calculated |
“This is calculated by an ECM by subtracting the front engine right exhaust manifold temperature from the front engine left exhaust manifold temperature.” |
270 |
ENG FUEL RATE F |
Engine Fuel Rate Front |
33 |
Calculated |
“The rate at which fuel is being used by the front engine.” |
271 |
ENG SPD F |
Engine Speed Front |
33 |
Frequency |
“The actual rotational speed of the crankshaft on the front engine.” |
273 |
F TRBO IN PRES |
Engine Turbo Inlet Pressure Front |
33 |
Analog |
“The pressure (absolute) of the air coming into the right turbo for the front engine.” |
274 |
F LO BOOST PRES |
Low Boost Pressure Front |
49 |
Calculated |
“This parameter monitors the warning status parameter of the engine ECM to see if the boost pressure is low.” |
275 |
ENG DERATE R |
Rear Engine Power Derate percentage |
34 |
Analog |
“Indicates the present rear engine power derate percentage. Zero indicates the engine is not derated.” |
276 |
GOV STAT R |
Slave Governing Status Rear Engine |
34 |
Calculated |
“Indicates the governing status (ALONE or SLAVE) of the rear engine slave ECM.” |
277 |
R AFTRCLR TEMP |
Rear Aftercooler Temperature |
34 |
PWM |
“The temperature of the coolant in the rear engine aftercooler system.” |
278 |
BOOST PRES R |
Engine Turbo Outlet (Boost) Pressure Rear |
34 |
Analog |
“The pressure on the compressor discharge side of the turbocharger of the rear engine.” |
279 |
ENG LOAD R |
Engine Load Rear |
34 |
Calculated |
“The actual percentage value of rear engine load.” |
280 |
ENG OIL PRES R |
Engine Oil Pressure Rear |
34 |
Analog |
“The oil pressure in the rear engine lubrication system. ” |
281 |
ENG STATUS R |
Engine Status Rear |
34 |
Calculated |
“The rear engine status. This determines the priority of engine status messages displayed on service tools.” |
282 |
WASTEGATE POS R |
Wastegate Position Rear |
34 |
Analog |
“The position of the wastegate valve on the rear engine turbocharger (outlet). The wastegate position sensor has an output that changes in voltage as the wastegate valve position changes. From this voltage, the engine ECM calculates the wastegate position.” |
283 |
FUEL FLTR R |
Engine Fuel Filter Status Rear |
34 |
Switch |
“The status (PLUGGED or OK) of the rear engine fuel filter.” |
285 |
R RT-LT EXH TEMP |
Rear Right Minus Left Exhaust Temperature |
49 |
Calculated |
“This is calculated by VIMS by subtracting the rear engine left exhaust manifold exhaust temperature from the rear engine right exhaust manifold exhaust temperature.” |
286 |
ENG FUEL RATE R |
Engine Fuel Rate Rear |
34 |
Calculated |
“The rate at which fuel is being used by the rear engine.” |
287 |
ENG SPD R |
Engine Speed Rear |
34 |
Frequency |
“The actual rotational speed of the rear engine crankshaft.” |
289 |
OIL PRES R LO |
Low Oil Pressure Rear |
49 |
Switch |
“This parameter monitors the engine status parameter from the engine ECM to see if the rear engine oil pressure is low.” |
290 |
EXH TEMP LTR |
Engine Left Rear Turbo Exhaust Temperature |
34 |
PWM |
“The temperature of the exhaust on the left side of the rear engine.” |
291 |
EXH TEMP RTR |
Engine Right Rear Turbo Exhaust Temperature |
34 |
PWM |
“The temperature of the exhaust on the right side of the rear engine.” |
292 |
TRBO IN PRES R |
Engine Turbo Inlet Pressure Rear |
34 |
Analog |
“The pressure (absolute) coming into the right turbo the front engine (uses atmospheric pressure).” |
293 |
AIR FLTR R |
Engine Peak Air Filter (Restriction) Rear |
34 |
Calculated |
“Reads the peak air filter restriction of the rear engine. ” |
294 |
CNKCASE PRES R |
Engine Crankcase Pressure Rear |
34 |
PWM |
“The pressure inside the crankcase of the rear engine. This pressure reading remains constant with changes in the altitude. ” |
295 |
ENG COOL TEMP R |
Engine Coolant Temperature (Jacket) Rear |
34 |
Analog |
“The coolant temperature in the rear engine cooling system. ” |
296 |
ENG OIL FLTR R |
Engine Oil Filter Differential Pressure (Gauge) Rear |
34 |
Switch |
“The pressure drop across the rear engine oil filter.” |
297 |
ENG OIL LVL R |
Engine Oil Level Rear |
34 |
Switch |
“The level of the oil in the rear engine.” |
298 |
BOOST PRES HI R |
High Boost Pressure Rear |
49 |
Switch |
“This parameter monitors the warning status of the rear engine ECM to see if high boost pressure exists.” |
299 |
BOOST PRES LO R |
Low Boost Pressure Rear |
49 |
Switch |
“This parameter monitors the warning status of the rear engine ECM to see if boost pressure is low.” |
303 |
PT OIL FLTR |
Power Train Oil Filter |
49 |
Switch |
“The status of the Power Train Oil Filter (PLUGGED or OK). When the pressure across the filter is greater than the specified pressure, the switch plunger moves and allows the switch contacts to open telling VIMS that the filter is PLUGGED. With normal operation, meaning acceptable pressure drop, the switch contacts are closed and the circuit is grounded. Cold oils often cause a known filter restriction, so VIMS ignores warnings (open switch) when oil temperature is below about 125 degrees F.” |
305 |
TRN GEAR |
Transmission Gear |
81 |
Switch |
“This is calculated by the transmission ECM and indicates the actual gear that the transmission is in.” |
306 |
GEAR SELECT |
Transmission Cane Select |
81 |
Calculated |
“The gear that the operator has selected in the machine cab. A switch on the gear select lever converts lever position into digital code for use by the transmission ECM. ” |
310 |
TC FLTR |
Torque Converter Filter (Bypass) |
49/81 |
Switch |
“The status of the torque converter inlet oil filter (PLUGGED or OK). When the pressure across the filter is greater than the specified pressure, the switch plunger moves and allows the switch contacts to open telling VIMS that the filter is plugged. With normal operation, the switch contacts are closed and the circuit is grounded. Cold oils often cause a known filter restriction, so VIMS ignores warnings (open switch) when oil temperature is below about 125 degrees F.” |
311 |
TC OUT SPD |
Torque Converter Output Speed |
27/49/81 |
Frequency |
“The speed of the torque converter output shaft. The sensor sends a signal to an ECM that is proportional in frequency depending on the torque converter output shaft speed. The ECM then calculates the speed based upon the frequency that is received.” |
312 |
TC SCREEN |
Torque Converter Screen |
49/81 |
Switch |
“The status of the torque converter outlet screen (filter) (PLUGGED or OK). As the torque converter screen becomes PLUGGED, the pressure across the screen causes the torque converter screen to be bypassed. When this bypass occurs, this switch opens telling VIMS that the torque converter screen needs to be replaced or cleaned.” |
313 |
TC OUT TEMP |
Torque Converter Outlet Temperature |
49/81 |
PWM |
“The oil temperature on the outlet side of the torque converter. VIMS receives a signal that changes in pulse width as the torque converter outlet oil temperature changes. VIMS then determines the temperature from the pulse width that it receives.” |
314 |
TC TEMP |
Torque Converter Temperature |
49 |
PWM |
“The oil temperature on the outlet of the torque converter. VIMS receives a signal that changes in pulse width as the torque converter oil temperature changes. VIMS then determines the temperature from the pulse width that it receives.” |
315 |
TC OUT PRES |
Torque Converter Outlet Pressure |
49 |
PWM |
“The oil pressure on the outlet side of the torque converter. VIMS receives a signal that changes in pulse width as the pressure changes. VIMS then calculates the pressure according to the pulse width that it receives.” |
322 |
QUICKSHIFT SW |
Quickshift Switch Position |
81 |
Calculated |
“The position of the quickshift switch (ON or OFF).” |
323 |
LUC ENABLE |
Lockup Clutch Enable Switch Position |
81 |
Switch |
“The position of the lockup clutch enable switch (ON or OFF).” |
324 |
PMP DRIVE TEMP |
Pump Drive Oil Temperature |
81 |
PWM |
“The actual implement pump oil temperature. VIMS receives a signal that changes in pulse width as the pump oil temperature changes. VIMS then determines the temperature from the pulse width that is received.” |
325 |
DIFF TEMP |
Differential Temperature (Oil) |
49 |
PWM |
“The oil temperature inside of the differential axle. VIMS receives a signal that changes in pulse width as the differential oil temperature changes. VIMS then determines the temperature from the pulse width that it receives.” |
326 |
DIFF CHIP |
Differential Chip (Detector) |
49 |
Switch |
“This switch notifies VIMS if chips have been detected in the differential. As metal chips collect on the magnetic contacts of the switch, a short circuit is made from one terminal to the other causing a closed circuit to ground. During normal operation, the switch is in the open position. The switch is considered closed when the resistance between the two switch terminals is between zero and approximately 2K ohms.” |
327 |
DIFF FLTR SW |
Differential Filter Switch (Bypass) |
30/49/116 |
Switch |
“The status of the differential axle oil filter (PLUGGED or OK). When the pressure across the filter is greater than the specified pressure, the switch plunger moves and allows the switch contacts to open telling VIMS that the differential filter is PLUGGED. With normal operation, meaning acceptable pressure drop, the switch contacts are closed to ground.” |
328 |
DIFF LUBE PRES |
Differential Lube Pressure |
30/49/116 |
PWM |
“The lubrication pressure within the differential axle housing. A pressure sensor sends to an ECM a pulse that varies in width as pressure changes. The ECM then calculates the pressure according to the pulse width that it receives. The actual pressure that would indicate a low diff lube pressure condition is 34 kPa (4.9 psi) on D trucks. The high diff lube pressure value is 1276 kPa (185.0 psi) Per the VIMS Events and condition, Event ID 2934 has an actuate value of 1 and deactuate of 0. These are not representative of pressures, but are actually values that are seen from the Brake ECM. Here is a description of the logic: The VIMS ECM reads a bit wise PID (Powertrain Warning Status) from the Brake ECM. When a specific bit in this parameter is set to 1, this indicates that there is a Low Differential Lube Pressure condition on this machine. If this is detected by VIMS, and VIMS also detects that the Rear Axle Pump Drive Oil Divert Solenoid Status is Off (0), VIMS will create the event with ME# 2934. The actual pressure that would indicate a low diff lube pressure condition is 34 kPa (4.9 psi) on D trucks.” |
329 |
TRN P1 PRES |
Transmission Pressure P1 |
81 |
PWM |
“The transmission P1 (control system) pressure.” |
330 |
TRN P2 PRES |
Transmission Pressure P2 |
81 |
PWM |
“The transmission P2 (clutch-fill) pressure.” |
331 |
IMPLR CLTCH PRES |
Impeller Clutch Pressure |
81 |
PWM |
“The impeller clutch pressure. A pressure sensor sends to an ECM a pulse that varies in width as pressure changes. The ECM then calculates the pressure according to the pulse width that is received.” |
332 |
LUC SOL CMD |
Lockup Clutch Current (Amp) Percentage |
81 |
Calculated |
“The solenoid command (or current) as a percentage of maximum which is being delivered to the lockup clutch solenoid.” |
333 |
RIMPULL STATUS |
Reduced Rimpull Status |
81 |
Switch |
“The status (ACTIVE or INACTIVE) of the reduced rimpull feature.” |
337 |
TRN IN SPD |
Transmission Input Speed |
81 |
Frequency |
“The actual rotational speed of the output shaft of the torque converter which is the input to the transmission.” |
339 |
TRN LATCH PRES |
Transmission Latching Pressure |
81 |
Frequency |
“The transmission latching pressure. The transmission ECM receives a signal to determine if the transmission is latched or unlatched.” |
340 |
TRN LCKOUT ST |
Transmission Lockout Status |
81 |
Calculated |
“The status of the transmission lock, which inhibits the transmission from going into gear while the service technician is working on the machine.” |
341 |
TRN OIL LVL |
Transmission Oil Level |
81 |
PWM |
“The status of the transmission oil level.” |
342 |
TRN OIL PRES |
Transmission Oil Pressure |
81 |
PWM |
“The transmission lube oil pressure.” |
343 |
TRN LCKOUT SW |
Transmission Lockout Switch |
81 |
Calculated |
“The position of the transmission control lever in the cab: ” REVERSE FORWARD NEUTRAL NOT-IN-REVERSE |
346 |
TRN COLD MODE |
Transmission Cold Mode |
81 |
Calculated |
“Indicates the cold mode status (active or inactive) as calculated by the transmission ECM.” |
347 |
TRN OUT SPD 2 |
Transmission Output Speed 2 |
81 |
Frequency |
“The speed of the transmission output shaft. This signal comes through the transmission speed distributor and is sent to the transmission ECM. The transmission output speed is directly proportional to ground speed.” |
349 |
TRN GEAR |
Transmission Gear |
27/81 |
Switch |
“This is calculated by EPTC (electronic programmable transmission ECM) or transmission ECM and indicates the actual gear that the transmission is in.” |
350 |
TRN LUBE TEMP |
Transmission Lube Temperature |
49/81 |
PWM |
“The transmission lubrication oil temperature. VIMS receives a signal that changes in pulse width as the transmission lubrication oil temperature changes. VIMS uses the pulse width that it receives to determine the oil temperature.” |
351 |
GEAR SELECT |
Gear Select (By Operator) |
27/81 |
Switch |
“The gear that the operator has selected in the machine cab. A switch on the gear select lever converts lever position into digital code for use by the transmission ECM. (used on the 797 instead of 306 due to the difference in gear codes)” |
354 |
PREVIOUS GEAR |
Previous Gear |
27 |
Calculated |
“No longer used.” |
355 |
TRN OUT SPD |
Transmission Out Speed |
27/81 |
Frequency |
“The speed of the transmission output shaft. This signal goes through the transmission speed distributor (OHT) and is sent to the transmission ECM. The transmission output speed is directly proportional to ground speed.” |
355 |
TRN OUT SPD1 |
Transmission Output Speed 1 |
81 |
Frequency |
“The speed of the transmission output shaft. This signal goes through the transmission speed distributor (OHT) and is sent to the transmission ECM. The transmission output speed is directly proportional to ground speed.” |
356 |
TRN CHRG FLTR |
Transmission Charge Filter (Bypass) |
49/81 |
Switch |
“The status of the transmission charge filter (PLUGGED or OK). The transmission charge line supplies oil to the hydraulic control valves of the transmission. When the pressure across the filter is greater than the specified pressure, the switch plunger moves and allows the switch contacts to open, telling VIMS that the filter is PLUGGED.” |
357 |
TRN LUBE FLTR |
Transmission Lube Filter (Bypass) |
49 |
Switch |
“The status of the transmission lubrication filter (PLUGGED or OK). When the pressure across the filter is greater than the specified pressure, the switch plunger moves and allows the switch contacts to open telling VIMS that the filter is plugged. With normal operation, meaning acceptable pressure drop, the switch contacts are closed to ground. The transmission lube circuit provides lubrication to the clutch disks, bearings, etc.” |
358 |
TRN SLIP |
Transmission Slip (OHT) |
27 |
Calculated |
“The degree to which the transmission is slipping at the completion of a shift. This is calculated by the transmission ECM. In this calculation, the transmission input and output speeds are compared. This time is the summation of time for the transmission control solenoids (up/dowm), actuator the up/down solenoid control, clutch fill, and actual slippage of the transmission plates/disk.” |
359 |
LCKUP SLIP |
Lockup Slip |
27 |
Calculated |
“The degree to which the torque converter lockup clutch is slipping when entering the lockup state. This is calculated by the transmission ECM. In this calculation, the torque converter input and output speeds are compared. Total sliptime is made up of individual actuation times much like parameter 358.” |
360 |
GEAR CHNG CODE |
Gear Change Code |
27 |
Calculated |
“Used in trends. Reads the gear change code of the slip packet. Calibrated by the transmission control.” |
361 |
GEAR MVMT TIME |
Gear Movement Time |
37 |
Calculated |
“Used in trends. Reads the gear movement time of the slip packet. Calibrated by the transmission control.” |
362 |
TRN LUBE TEMP |
Transmission Lube Temperature |
49 |
PWM |
“The temperature of the transmission lubrication oil. VIMS receives a signal that changes in pulse width as the transmission lubrication oil temperature changes. VIMS then uses the pulse width that it receives, to determine the transmission lubrication temperature.” |
364 |
TRN PMP PRES |
Transmission (Oil) Pump Pressure |
49 |
PWM |
“The lube oil pressure within the transmission. The pressure sensor sends to VIMS a pulse that varies in width as the pressure changes. VIMS then calculates the pressure according to the pulse width that is received.” |
365 |
TRN FLTR |
Transmission Filter (Bypass) |
49 |
Switch |
“The status of the transmission oil filter (PLUGGED or OK). When the pressure across the filter is greater than the specified pressure, the switch plunger moves allowing the switch contacts to open telling VIMS that the filter is PLUGGED. With normal operation the switch contacts are closed and the circuit is grounded. Cold oils often cause a known filter restriction, so VIMS ignores warnings (open switch) when oil temperature is below about 125 degrees F.” |
366 |
NTRL SW |
Neutral Switch |
27/81 |
Switch |
“This tells the transmission ECM whether the transmission shift linkage is the neutral position. When the switch is in the neutral position, the operator is allowed to crank the engine.” |
369 |
NTLRZR SW |
Neutralizer Pressure Switch Position |
81 |
Switch |
“Reads the position (RUN or NEUTRAL) of the neutralizer pressure switch.” |
370 |
RIMPULL % |
Controlled Rimpull Percentage |
81 |
Calculated |
“Used to read percent of maximum rimpull which is being controlled by the transmission ECM based on reduced rimpull setting and torque converter pedal modulation. This is not the actual or available rimpull, which is affected by equipment operation.” |
371 |
IMPLR CLCH CUR |
Impeller Clutch Current (Amp) Percentage |
81 |
Calculated |
“The current as a percentage of maximum which is being delivered to the impeller clutch solenoid from the transmission ECM.” |
372 |
RIMPULL SELECT2 |
Reduced Rimpull Selection Switch Position |
81 |
Switch |
“The position of the reduced rimpull selection switch.” LOW MEDIUM LOW MEDIUM HIGH HIGH |
373 |
RIMPULL STATUS 2 |
Reduced Rimpull ON/OFF Switch Position |
81 |
Switch |
“The position of the reduced rimpull ON/OFF switch.” |
374 |
PARKBK |
Parking Brake Pressure Switch Status |
81 |
Switch |
“Used to read the status of the parking brake pressure switch. Pressure is LOW (open) (parking brake is engaged) Pressure is HIGH (closed) (parking brake is disengaged).” |
376 |
BRK PRES SW |
Braking System Pressure Switch |
116 |
Switch |
“The present state of the service brake. ON (switch is closed) or OFF (switch is open). ” |
377 |
BRK PUMP SPD |
Braking Cooling Pump Speed |
116 |
Sensor |
“The speed of the brake cooling pump (0 to 2000 RPM)”. |
378 |
BRK COOL FLTR F |
Front Brake Cooling Filter Bypass |
87 |
Switch |
“The status of the front brake cooling filter (PLUGGED or OK).” |
379 |
PARKBK DR STATUS |
Parking Brake Dragging Status |
116 |
Calculated |
“The dragging status of the parking brakes. Dragging brake means the brake pressure sensorindicatesthat the parking brake is engaged, however the operator is not asking to engage the brake and the brake ECM is not trying to engage the brake.” |
380 |
RETRDR |
Retarder |
83/116 |
Switch |
“The status of the retarder system. This parameter will display either an ON or OFF state.” |
381 |
BRK COOL FLTR R |
Brake Cooling Filter Bypass Rear |
116 |
Switch |
“The status of the rear brake cooling filter (PLUGGED or OK).” |
382 |
BRK LOCKDN |
Remote Park Brake Set |
116 |
Switch |
“The status of the parking brake lock. The active (ON) status indicates that the parking brake is engaged. The inactive (OFF) status indicates that the parking brake is disengaged.” |
415 |
SERV BRK PEDAL |
Service Brake Pedal Position Status |
36 |
Switch |
“Read the position of the service brake pedal as released (OFF) or depressed (ON).” |
416 |
PARKBK PRES LTR |
Left Rear Parking Brake Oil Pressure |
116 |
PWM |
“The oil pressure for the left rear parking brake. The pressure sensor sends to VIMS a pulse that varies in width as the pressure changes. VIMS then calculates the pressure according to the pulse width that it receives.” |
417 |
PARKBK PRES RTR |
Right Rear Parking Brake Oil Pressure |
116 |
PWM |
“The oil pressure for the right rear parking brake. The pressure sensor sends to VIMS a pulse that varies in width as the pressure changes. VIMS then calculates the pressure according to the pulse width that it receives.” |
418 |
LTR WHEEL SPD |
Left Rear Wheel Speed |
27/116 |
Frequency |
“Used to read the actual rotational speed of the left rear axle in RPM.” |
419 |
RTR WHEEL SPD |
Right Rear Wheel Speed |
27/116 |
Frequency |
“Used to read the actual rotational speed of the right rear axle in RPM.” |
436 |
RTR-RTF BRK TEMP |
Right Rear Minus Right Front Brake Temperature |
49 |
Calculated |
“This is calculated by VIMS, by subtracting the right front brake temperature from the right rear brake temperature.” |
437 |
LTR-LTF BRK TEMP |
Left Rear Minus Left Front Brake Temperature |
49 |
Calculated |
“This is calculated by VIMS, by subtracting the left front brake temperature from the left rear brake temperature.” |
438 |
STRG OIL PRES |
Steering Pump Oil Pressure Sensor |
49 |
PWM |
“The steering oil pressure at the pump outlet. VIMS receives a signal that changes in pulse width as the steering oil pressure changes. VIMS then determines the pressure from the pulse width that it receives.” |
440 |
STRG OIL PRES |
Steering Pump Pressure |
49 |
Switch |
“Notifies VIMS of low steering oil pressure. With low pressure the switch would be open. In normal operation, the switch is closed to ground.” |
441 |
LO STRG PRES |
Low Steering Pressure |
49 |
Switch |
“Notifies VIMS of low oil pressure at the pump outlet in the steering system. With low pressure, the switch will be open. In normal operation, the switch is closed to ground.” |
442 |
HI STRG PRES |
High Steering Pressure |
49 |
Switch |
“Notifies VIMS of low oil pressure at the accumulator outlet in the steering system. With low pressure, the switch should be open to ground. In normal operation, the switch is closed to ground.” |
444 |
STRG OIL TEMP |
Steering Oil Temperature |
49 |
PWM |
“The main steering system oil temperature. VIMS receives a signal that changes in pulse width as the main steering system oil temperature changes. VIMS then determines the oil temperature from the pulse width that it receives.” |
445 |
FAN DRIVE FLTR |
Fan Drive Oil Filter Bypass |
116 |
Switch |
“The status of the Fan Drive Oil Filter Bypass (PLUGGED or OK). When the pressure across the filter is greater than the specified pressure, the switch plunger moves and allows the switch contacts to open telling VIMS that the filter is plugged. With normal operation, the switch contacts are closed and the circuit is grounded. Cold oils often cause a known filter restriction, so VIMS ignores warnings (open switch) when oil temperature is below about 125 degrees F.” |
445 |
STRG OIL FLTR |
“Steering Oil Filter” |
49 |
Switch |
“The status of the main steering system oil filter (PLUGGED or OK). When the pressure across the filter is greater than the specified pressure, the switch plunger moves and allows the switch contacts to open telling VIMS that the filter is plugged. With normal operation, the switch contacts are closed and the circuit is grounded. Cold oils often cause a known filter restriction, so VIMS ignores warnings (open switch) when oil temperature is below about 125 degrees F.” |
447 |
STRG OIL LEVEL |
Steering Oil Level |
49 |
Switch |
“This switch notifies VIMS of the status of oil level in the main steering system (LO or OK). The switch opens when steering oil level is less than the specified. During normal operation, the switch is closed to ground.” |
448 |
STRG/TRN LCK |
Steering/Transmission Lock |
49 |
Switch |
“The status of the steering and transmission lockout systems. A switch with two outputs (normally closed and normally open) is used as inputs to notify the transmission ECM of the lockout condition. At any given time one input must always be connected to ground and the other must be open. If this case is not so, the transmission ECM knows that there is a failure in the system. When steering/transmission lockout is active, the steering and transmission systems are not allowed to function.” |
449 |
PRI STRG PRES |
Primary Steering Pressure |
49 |
Switch |
“The status of the oil pressure on the primary side of the steering system (LO or OK). This pressure switch is normally connected to ground. When the pressure becomes lower than a specified level, the switch opens notifying VIMS that there is low oil pressure.” |
450 |
F BRK OIL TEMP |
Front Brake Oil Temperature |
49 |
PWM |
“The temperature of the cooling oil from both front brakes. VIMS receives a signal that changes in pulse width as the front brake system cooling oil changes temperature. VIMS then determines the temperature from the pulse width that it receives.” |
451 |
R BRK OIL TEMP |
Rear Brake Oil Temperature |
49 |
PWM |
“The temperature of the cooling oil from both rear brakes. VIMS receives a signal that changes in pulse width as the rear brake system cooling oil changes temperature. VIMS then determines the temperature from the pulse width that it receives.” |
452 |
BRK/AIR PRES |
Brake Air Pressure |
49 |
PWM |
“The air pressure in the braking system. The pressure sensor sends to VIMS a signal that varies in width as the brake air system pressure changes. VIMS then calculates the pressure according to the pulse width that is received.” |
453 |
PARKBK |
Parking Brake |
49/81/ 116 |
Switch |
“The status of the parking brake (ON or OFF). With the parking brake off the switch is open, but when the parking brake is on, a ground signal is sent to an ECM. A warning message will be generated if the parking brake is engaged while the machine is not in neutral.” |
454 |
BRK FLTR |
Brake Filter |
49 |
Switch |
“The status of the filter in the oil cooling line for the brakes (PLUGGED or OK). When the pressure across the filter is greater than the specified pressure, the switch plunger moves and allows the switch contacts to open telling VIMS that the filter is PLUGGED.” |
455 |
BRK TEMP |
Brake Temperature |
49 |
PWM |
“The temperature of the brake oil. VIMS receives a signal that changes in pulse width as the brake oil temperature changes. VIMS then determines the temperature from the pulse width that it receives.” |
456 |
BRK STROKE |
Brake Stroke |
49 |
Switch |
“This is a switch(s) that tells VIMS if the brake master oil line pressure is too low or if one of the master brake cylinders (there can be more than one brake stroke switch, in which case they would be wired in a series circuit) has overstroked. In a failed state, the normal switch path to ground will be opened, notifying VIMS that there is a problem with at least one of the brake master cylinders.” |
457 |
PRI BRK PRES |
Primary Brake Pressure |
49 |
Switch |
“This is the status of the primary brake pressure switch. In normal operation the switch is closed to ground, but when the brake is applied the switch is open.” |
458 |
SEC BRK PRES |
Secondary Brake Pressure |
49 |
Switch |
“The status of the secondary brake lever pressure switch. The status of the secondary brake pressure switch is closed when the secondary brake lever has been applied (parking brake).” |
460 |
LTF BRK TEMP |
Left Front Brake Temperature |
49/116 |
PWM |
“The cooling oil temperature from the left front brake. VIMS receives a signal that changes in pulse width as the temperature of the oil coming from the left front brake changes. VIMS then determines the temperature from the pulse width that is received.” |
461 |
LTR BRK TEMP |
Left Rear Brake Temperature |
49/116 |
PWM |
“The cooling oil temperature from the left rear brake. VIMS receives a signal that changes in pulse width as the temperature of the oil coming from the left rear brake changes. VIMS then determines the temperature from the pulse width that is received.” |
462 |
RTF BRK TEMP |
Right Front Brake Temperature |
49/116 |
PWM |
“The oil temperature from the right front brake. VIMS receives a signal that changes in pulse width as the temperature of the oil coming from the right front brake changes. VIMS then determines the temperature from the pulse width that is received.” |
463 |
RTR BRK TEMP |
Right Rear Brake Temperature |
49/116 |
PWM |
“The cooling oil temperature from the right rear brake. VIMS receives a signal that changes in pulse width as the temperature of the oil coming from the right rear brake changes. VIMS then determines the temperature from the pulse width that is received.” |
464 |
RTF-LTF BRK TEMP |
Right Front Minus Left Front Brake Temperature |
49 |
Calculated |
“This is calculated by VIMS by subtracting the left front brake temperature from the right front brake temperature.” |
465 |
RTR-LTR BRK TEMP |
Right Rear Minus Left Rear Brake Temperature |
49 |
Calculated |
“VIMS calculates this value by subtracting the left rear brake temperature from the right rear brake temperature.” |
466 |
PARKBK PRES SW |
Parking Brake Filter Switch |
49 |
Switch |
“The parking brake filter status (PLUGGED or OK). When the pressure across the filter is greater than the specified pressure, the switch plunger moves and allows the switch contacts to open telling VIMS that the filter is PLUGGED. With normal operation, the switch contacts are closed and the circuit is grounded.” |
467 |
BRK COOL FLTR F |
Front Brake Cooling Filter Status |
49 |
Switch |
“The status of the front brake cooling filter. When the pressure across the filter is greater than the specified pressure, the switch plunger moves and allows the switch contacts to open telling VIMS that the filter is PLUGGED. With normal operation, the switch contacts are closed and the circuit is grounded.” |
468 |
BRK COOL FLTR R |
Rear Brake Cooling Filter Status |
49 |
Switch |
“The status of the rear brake cooling filter. When the pressure across the filter is greater than the specified pressure, the switch plunger moves and allows the switch contacts to open telling VIMS that the filter is PLUGGED. With normal operation, the switch contacts are closed and the circuit is grounded.” |
470 |
F BRK OIL PRES |
Front Brake Oil Pressure |
49 |
PWM |
“The oil pressure at the inlet of the front brakes. The pressure sensor sends VIMS a pulse that varies in width as the pressure changes. VIMS then calculates the pressure according to the pulse width that is received.” |
471 |
R BRK OIL PRES |
Rear Brake Oil Pressure |
49 |
PWM |
“The oil pressure at the inlet of the rear brakes. The pressure sensor sends VIMS a pulse that varies in width as the pressure changes. VIMS then calculates the pressure according to the pulse width that is received.” |
472 |
F BRK ACUM PRES |
Front Brake Accumulator Pressure |
49 |
Switch |
“The front brake accumulator pressure. This pressure switch is normally connected to ground. When the pressure becomes lower than the desired level, the pressure switch opens, notifying VIMS that there is low pressure in the front brake accumulator system.” |
473 |
R BRK ACUM PRES |
Rear Brake Accumulator Pressure |
49 |
Switch |
“The rear brake accumulator pressure. This pressure switch is normally connected to ground. When the pressure becomes lower than the desired level, the pressure switch opens, notifying VIMS that there is low pressure in the rear brake accumulator system.” |
474 |
F AXLE OIL TEMP |
Front Axle Oil Temperature |
49 |
PWM |
“The temperature of the oil within the front axle. VIMS receives a signal that changes in pulse width as the front axle oil temperature changes. VIMS then determines the temperature from the pulse width that is received.” |
475 |
R AXLE OIL TEMP |
Rear Axle Oil Temperature |
49 |
PWM |
“The temperature of the oil within the rear axle. VIMS receives a signal that changes in pulse width as the rear axle oil temperature changes. VIMS then determines the temperature from the pulse width that is received.” |
476 |
PARKBK CAB SW |
Parking Brake Cab Switch |
81 |
Switch |
“The status of the switch in the cab that is used to engage or disengage the parking brake. The switch is either in the parking brake engaged position (OPEN) or the parking brake disengaged position (CLOSED).” |
477 |
BRK ACUM PRES |
Brake Accumulator Pressure |
49 |
Switch |
“The brake accumulator pressure. This pressure switch is normally closed to ground. When the pressure becomes lower than the desired level, the switch opens notifying VIMS that there is low pressure in the brake accumulator system.” |
478 |
RT TRL BRK TEMP |
Right Trailer Brake (Oil) Temperture |
49 |
PWM |
“The oil temperature within the right trailer brake. The temperature sensor sends to VIMS a pulse that varies in width as the temperature changes. VIMS then calculates the temperature according to the pulse width that is received.” |
479 |
LT TRL BRK TEMP |
Left Trailer Brake (Oil) Temperature |
49 |
PWM |
“The oil temperature within the left trailer brake. The temperature sensor sends to VIMS a pulse that varies in width as the temperature changes. VIMS then calculates the temperature according to the pulse width that is received.” |
480 |
TRLBRKC IN TEMP |
Trailer Brake Cooler (Oil) Inlet Temperature |
49 |
PWM |
“The trailer brake oil temperature on the inlet side of the trailer brake oil cooler. VIMS receives a signal that changes in pulse width as the cooler inlet oil temperature changes. VIMS then determines the temperature from the pulse width that it receives.” |
481 |
TRLBRKC OUT TEMP |
Trailer Brake Cooler (Oil) Outlet Temperature |
49 |
PWM |
“The trailer brake oil temperature on the outlet side of the trailer brake oil cooler. VIMS receives a signal that changes in pulse width as the cooler outlet oil temperature changes. VIMS then determines the temperature from the pulse width that is received.” |
482 |
TRL FLTR |
Trailer Filter Plug |
49 |
Switch |
“The status of the trailer brake oil filter. The switch will open in the case of a plugged filter.” |
483 |
TRL BRK STROKE |
Trailer Brake Stroke |
49 |
Switch |
“This is a switch(s) that tells VIMS if the trailer brake master oil line pressure is too low, or if one of the trailer brake master cylinders (There can be more than one brake stroke switch, in which case they would be wired in a series circuit) has overstroked. If one of these conditions are met VIMS would be notified that there is a problem with at least one of the master trailer brake cylinders.” |
484 |
STRG TEMP SW |
Steering Oil Temperature Switch |
49 |
Switch |
“The steering oil temperature status. If the temperature gets above a predetermined level, the switch will open to indicate that steering oil temperature is too high.” |
485 |
ENG OIL FLTR |
Engine Oil Filter Differential Pressure |
36 |
Switch |
“The pressure drop across the engine oil filter. When the pressure across the filter is greater than the specified pressure, the switch plunger moves and allows the switch contacts to open telling VIMS that the filter is PLUGGED. With normal operation, the switch contacts are closed and the circuit is grounded.” |
488 |
STG COOL FLTR |
Steering Cooling Filter Status |
49 |
Switch |
“The status of the steering cooling filter (OK or PLUGGED). When the pressure across the filter is greater than the specified pressure, the switch plunger moves and allows the switch contacts to open telling VIMS that the filter is PLUGGED. With normal operation, the switch contacts are closed and the circuit is grounded.” |
490 |
STRG RTN FLTR |
Steering Return to Tank Filter Status |
49 |
Switch |
“The status of the steering return to tank filter (OK or PLUGGED). When the pressure across the filter is greater than the specified pressure, the switch plunger moves and allows the switch contacts to open telling VIMS that the filter is PLUGGED. With normal operation, the switch contacts are closed and the circuit is grounded.” |
491 |
LT STRG CDRN |
Left Steering Case Drain Pump Temperature |
49 |
PWM |
“The temperature of the oil within the left steering case drain pump. VIMS receives a signal that changes in pulse width as the left steering case drain pump temperature changes. VIMS then determines the temperature from the pulse width that is received.” |
492 |
RT STRG CDRN |
Right Steering Case Drain Pump Temperature |
49 |
PWM |
“The temperature of the right steering case drain oil.” |
493 |
PARKBK FLTR |
Parking Brake Oil Filter Status |
116 |
Switch |
“The status of the parking brake oil filter. When the pressure across the filter is greater than the specified pressure, the switch plunger moves and allows the switch contacts to open telling VIMS that the filter is PLUGGED. With normal operation, the switch contacts are closed and the circuit is grounded.” |
494 |
LT STRG CDRN |
Left Steering Case Drain Oil Filter Status |
49 |
Switch |
“The status of the oil filter on the left steering case drain (OK or PLUGGED). When the pressure across the filter is greater than the specified pressure, the switch plunger moves and allows the switch contacts to open telling VIMS that the filter is PLUGGED. With normal operation, the switch contacts are closed and the circuit is grounded.” |
495 |
RT STRG CDRN |
Right Steering Case Drain Oil Filter Status |
49 |
Switch |
“The status of the oil filter on the right steering case drain (OK or PLUGGED). When the pressure across the filter is greater than the specified pressure, the switch plunger moves and allows the switch contacts to open telling VIMS that the filter is PLUGGED. With normal operation, the switch contacts are closed and the circuit is grounded.” |
498 |
F HI PRES FLTR |
Front High Pressure Filter |
49 |
Switch |
“The status of the front implement high pressure hydraulic oil filter. When the pressure across the filter is greater than the specified pressure, the switch plunger moves and allows the switch contacts to open telling VIMS that the filter is PLUGGED. With normal operation, the switch contacts are closed and the circuit is grounded.” |
499 |
R HI PRES FLTR |
Rear High Pressure Switch |
49 |
Switch |
“The status of the rear implement high pressure hydraulic oil filter. When the pressure across the filter is greater than the specified pressure, the switch plunger moves and allows the switch contacts to open telling VIMS that the filter is PLUGGED. With normal operation, the switch contacts are closed and the circuit is grounded.” |
500 |
HYD OIL TEMP |
Hydraulic Oil Temperature |
36/49 |
PWM |
“The hydraulic oil temperature. An ECM receives a signal that changes in pulse width as the hydraulic oil temperature changes. The ECM then determines the temperature from the pulse width that is received.” |
501 |
PMP IN VALVE |
Pump Inlet Valve |
49 |
Switch |
“These switches are attached to the inlet suction line for each hydraulic oil pump. They are located at the hydraulic oil tank. When the pump inlet valve is open, meaning that oil can flow, the switch is closed, and the circuit is grounded. There could be multiple switches wired in series on one particular machine, after which a switch(s) opens (meaning no oil flow), the ECM would know there is no oil flow in one or more circuits.” |
502 |
HYD OIL LVL |
Hydraulic Oil Level |
49 |
Switch |
“The status of the hydraulic oil level (LO or OK). With low hydraulic oil level, the switch will open. In normal operation, the switch is closed to ground.” |
503 |
CDRN FLTR |
Case Drain Filter |
49 |
Switch |
“The status of the case drain filter (PLUGGED or OK). As the case drain filter becomes PLUGGED, mechanically the machine causes the oil filter to be bypassed. When this filter is bypassed, the flow of oil in the bypass route opens a switch that tells VIMS that the filter is plugged. In normal operation the switch is closed to ground.” |
504 |
HI PRES FLTR |
High Pressure Filter |
49 |
Switch |
“This is a result obtained from up to eight high pressure filters. These high pressure filters are wired in a series circuit to ground. If any one of the filters becomes PLUGGED, the corresponding switch (circuit) opens, indicating that at least one of the high pressure filters is PLUGGED.” |
505 |
HOIST SCREEN |
Hoist Screen |
49 |
Switch |
“The status of the hoist screen (PLUGGED or OK). As a hoist screen becomes PLUGGED, mechanically the machine causes the hoist screen to be bypassed. When the bypass occurs, the flow of oil in the bypass route opens a switch that tells VIMS that the hoist screen needs to be replaced or cleaned. In normal operation the switch is closed to ground.” |
506 |
HYD RTN FLTR |
Hydraulic Return Filter |
49 |
Switch |
“This is the status of the hydraulic oil return line filter (PLUGGED or OK). As the hydraulic oil return line filter becomes PLUGGED, mechanically the machine causes the hydraulic oil return line filter to be bypassed. When this bypass occurs, the flow of oil in the bypass route opens a switch that tells VIMS that the hydraulic oil return filter needs to be replaced or cleaned.” |
511 |
HYD SYS PRES |
Hydraulic System Pressure |
49 |
Switch |
“The present pressure of the hydraulic system.” |
513 |
DIFF OIL LVL |
Differential Oil Level |
49 |
Switch |
“The status of the differential oil level (LO or OK). With low oil level the switch will open. In normal operation the switch is closed to ground.” |
515 |
HYD OIL LVL |
Hydraulic Oil Level |
49 |
Switch |
“The status of the hydraulic oil level (LO or OK). With low oil level, the switch will open. In normal operation, the switch is closed to ground.” |
516 |
HYD OIL TEMP |
Hydraulic Oil Temperature |
36/49 |
PWM |
“The hydraulic oil temperature. An ECM receives a signal that changes in pulse width as the hydraulic oil temperature changes. The ECM then determines the temperature from the pulse width that is received.” |
517 |
HYD OIL FLTR |
Hydraulic Oil Filter |
49 |
Switch |
“The status of the hydraulic oil filter (PLUGGED or OK). When the pressure across the filter is greater than the specified pressure, the switches plunger moves and allows the switch contacts to open telling VIMS that the filter is plugged. With normal operation, the switch contacts are closed and the circuit is grounded. Cold oils often cause a known filter restriction, so VIMS ignores warnings (open switch) when oil temperature is below about 125 degrees F.” |
518 |
HYD PILOT PRES |
Hydraulic Oil Pilot Pressure |
49 |
PWM |
“The oil pressure in the hydraulic pilot oil line. The machine ECM receives a signal that changes in pulse width as the hydraulic pilot oil pressure changes. The machine ECM then determines the pressure from the pulse width that is received.” |
519 |
ENG FAN BYPASS |
Engine Fan Bypass |
36/49 |
Calculated |
“Used to read and override the bypass valve position of the engine cooling fan. Override is accomplished through a PC that is running the Electronic Technician software only.” |
520 |
ENG FAN SPD |
Engine Fan Speed |
36/49 |
Frequency |
“The speed of the engine cooling fan shaft. The sensor mounted on the engine fan shaft generates a signal that varies in frequency as the cooling fan shaft varies in speed. An ECM, after receiving this signal determines the speed of the engine cooling fan.” |
521 |
HYD FAN SPD |
Hydraulic Fan Speed |
36/49 |
Frequency |
“The speed of the hydraulic oil cooling fan shaft. The sensor mounted on the hydraulic oil cooling fan shaft generates a signal that varies in frequency. An ECM, after receiving this frequency signal then determines the speed of the hydraulic oil cooling fan.” |
524 |
DIFF FAN |
Differential Fan |
30 |
Calculated |
“The status of the fan that is used to cool the differential axle oil (ON or OFF). This value is received from the Caterpillar Monitoring System over the CAT Data Link. ” |
525 |
HYD FAN BYPASS |
Hydraulic Fan Bypass |
36/49 |
Calculated |
“Used to read and override the bypass valve position of the cooling fan for the hydraulic oil. Override is accomplished through a PC that is running the Electronic Technician software only.” |
550 |
SYS AIR PRES |
System Air Pressure |
49 |
PWM |
“This is a measure of the air pressure in the main supply line for the machine. The sensor sends to VIMS a pulse that varies in width as the pressure changes. VIMS then calculates the pressure according to the signal that is received.” |
555 |
HYD LOOP FLTR |
Hydraulic Circuit Filter Status |
49 |
Switch |
“Used to read the status of the hydraulic circuit filter (OK or PLUGGED).” |
574 |
LFT LVR POS |
Lift Lever Position |
82 |
PWM |
“A percentage value that represents the position of the bucket hydraulic lift lever within the cab (within the full calibrated range of the lever). This should be a value from 0% to 100%. An ECM receives this signal that changes in pulse width as the lift lever position changes. The ECM then calculates the lift lever position from the pulse width that it receives.” |
576 |
LFT RAISE SOL1 |
Lift Raise Solenoid Number 1 |
82 |
Solenoid |
“The status of the number one pilot lift-raise solenoid that is used to control the lift cylinders. The two states for this solenoid are ON or OFF.” |
705 |
ATMOS PRES R |
Atmospheric Pressure Rear Engine |
34 |
Analog |
“The atmospheric (barometric) pressure on the outside of the machine. The atmospheric pressure sensor sends to the engine ECM a voltage that varies as the pressure changes. The engine ECM then calculates the pressure according to the voltage that is received.” |
706 |
HOIST RO PRES |
Hoist Rod End Pressure |
87 |
PWM |
“The oil pressure on the rod end of the hydraulic tilt cylinder. An ECM receives a square wave signal from the sensor that changes in frequency as the hydraulic tilt cylinder rod end oil pressure changes. The ECM then calculates the pressure from the frequency that is received.” |
707 |
HOIST HD PRES |
Hoist Head End Pressure |
87 |
PWM |
“The oil pressure on the head end of the hydraulic tilt cylinder. An ECM receives a square wave signal from the sensor that changes in frequency as the hydraulic tilt cylinder head end oil pressure changes. The ECM then calculates the pressure from the frequency that is received.” |
708 |
BODY ANGLE |
Body Position Sensor |
87 |
PWM |
“The angle that represents the body position. The angle is measured in reference from the down position (on the rail).” |
710 |
RTF-LTF SUSP CYL |
Right Front Minus Left Front Suspension Cylinder |
49 |
Calculated |
“This is calculated by VIMS by subtracting the left front suspension cylinder pressure from the right front suspension cylinder pressure.” |
711 |
RTR-LTR SUSP CYL |
Right Rear Minus Left Rear Suspension Cylinder |
49 |
Calculated |
“This is calculated by VIMS by subtracting the left rear suspension cylinder pressure from the right rear suspension cylinder pressure.” |
712 |
HOIST SCREEN |
Hoist Screen Bypass |
87 |
Switch |
“The status of the hydraulic hoist screen filter (PLUGGED or OK).” |
720 |
LTF SUSP CYL |
Left Front Suspension Cylinder |
49 |
Frequency |
“The left front suspension cylinder pressure. VIMS receives a square wave signal from the sensor that changes in frequency in respect to the change in the cylinder pressure. VIMS then calculates the pressure in the cylinder from the frequency that is received.” |
721 |
LTR SUSP CYL |
Left Rear Suspension Cylinder |
49 |
Frequency |
“The left rear suspension cylinder pressure. VIMS receives a square wave signal from the sensor that changes in frequency in respect to the change in the cylinder pressure. VIMS then calculates the pressure in the cylinder from the frequency that is received.” |
722 |
RTF SUSP CYL |
Right Front Suspension Cylinder |
49 |
Frequency |
“The right front suspension cylinder pressure. VIMS receives a square wave signal from the sensor that changes in frequency in respect to the change in the cylinder pressure. VIMS then calculates the pressure in the cylinder from the frequency that is received.” |
723 |
RTR SUSP CYL |
Right Rear Suspension Cylinder |
49 |
Frequency |
“The right rear suspension cylinder pressure. VIMS receives a square wave signal from the sensor that changes in frequency in respect to the change in the cylinder pressure. VIMS then determines the pressure in the cylinder from the frequency that is received.” |
724 |
BODY ANGLE |
Body Position Angle |
27 |
PWM |
“Used to read the angle of the body position. The angle is measured in reference from the down position (on the rail).” |
725 |
GND SPD |
Ground Speed |
27/81 |
Frequency |
“The speed of the machine relative to the ground. The sensor sends a signal to the transmission ECM that varies in frequency depending on the transmission output shaft speed. Then based on the frequency that the transmission ECM receives, the ground speed is determined.” |
726 |
BODY POS |
Body Position |
27 |
Switch |
“The position of the body (up or down). One use of this sensor (switch) is to tell the transmission ECM what the body position is so that ground speed can be limited with the body up.” |
727 |
BODY LVR |
Body Lever |
27 |
Switch |
“The status of the body raise/lower lever within the cab. The state of the body lever is up, down or float.” |
728 |
PAYLOAD |
Payload |
49 |
Calculated |
“The payload is calculated by VIMS based on pressures of the four suspension cylinders. The payload can change throughout a cycle, but the payload value returns to zero at the end of the payload cycle when the body raise/lower routine is performed (dumping of the load) (OHT).” |
729 |
PAYLOAD STATUS |
Payload Status |
49 |
Calculated |
“The status of the truck in a payload cycle. Examples of payload status are stopped empty, stopped loading, traveling loaded, dumping, traveling empty, etc. ” |
730 |
HAUL DISTANCE |
Haul Distance |
49 |
Calculated |
“The distance that has been traveled by the truck up to a present point in a payload cycle. Haul distance is calculated based on ground speed and travel time.” |
731 |
RT TRL SUSP CYL |
Right Trailer Suspension Cylinder Pressure |
59 |
Frequency |
“The oil pressure within the right trailer suspension cylinder. VIMS receives a square wave signal from the sensor that changes in frequency as the right trailer suspension cylinder pressure changes. VIMS then determines the pressure in the cylinder from the frequency that is received from the sensor.” |
732 |
LT TRL SUSP CYL |
Left Trailer Suspension Cylinder Pressure |
59 |
Frequency |
“The oil pressure at the left trailer suspension cylinder. VIMS receives a square wave signal from the sensor that changes in frequency as the left trailer suspension cylinder pressure changes. VIMS then determines the pressure in the cylinder from the frequency that is received from the sensor.” |
733 |
TRL DOOR POS |
Trailer Door Position |
59 |
PWM |
“The status of the trailer door (open or closed) (the door on the bottom of the trailer that is used for dumping). VIMS receives a signal that changes in pulse width as the trailer door position changes. VIMS then determines the position from the pulse width that is received.” |
734 |
TLT CYLHD PRES |
Tilt Cylinder Head Pressure |
49 |
Frequency |
“The oil pressure on the head end of the bucket tilt cylinder. An ECM receives a square wave signal from the sensor that changes in frequency in respect to the change in the cylinder pressure. The ECM then determines the pressure within the cylinder from the frequency that it receives from the sensor. Negative pressures will not be displayed.” |
737 |
GND SPD |
Ground Speed |
81 |
Calculated |
“Used to read the machine ground speed with directional indication. The signed data indicates the direction of travel: Negative is in reverse.” |
742 |
USER SHUTDN |
User Shutdown |
36 |
Switch |
“This tells the status of the user shutdown input. There are two states, on and off. When in the shutdown (ON) position (resulting from grounding this input) the engine ECM stops the engine.” |
743 |
SHUTDN SW |
Shutdown Switch |
36 |
Switch |
“The status of the machine remote shutdown switch. To activate this switch the red guard on the machine must be lifted and the switch in the on position. The engine ECM reads the switch, and after one second fuel injection will be stopped if the engine is running, or the engine will not be allowed to start if not running. Once the switch has been on, the key start switch must be turned off momentarily and then back on before the engine ECM will allow the engine to run again.” |
747 |
SWG HIPRES FLTR |
Swing High Pressure Filter |
49 |
Switch |
“The status (PLUGGED or OK) of the swing high pressure hydraulic oil filter.” |
749 |
AUTO LUBE PRES |
Auto Lube Pressure |
49 |
PWM |
The pressure in the lubrication line that feeds grease to the grease injectors of the lubrication system. The sensor that measures the pressure sends a pulse to VIMS that varies in width depending on the line pressure. VIMS then uses this signal (large wheel loaders) to calculate the lube pressure. |
751 |
AUTO LUBE |
Auto Lube (Status) |
49 |
Calculated |
“This is the operating status of the auto lube solenoid. There are several possible states. They are active, pending, warning, inactive, and terminate .” |
752 |
ENG FAN PMP PRES |
Engine Fan Pump Pressure |
36 |
Analog |
“The oil pressure in the hydraulic oil line to the engine cooling fan hydraulic motor. The engine ECM receives a signal that changes in voltage as the engine fan pump oil pressure changes. The engine ECM then determines the pressure from the voltage that is received.” |
754 |
SYS VOLTAGE |
System Voltage |
49 |
Calculated |
“The actual voltage that exists between the positive side of the electrical system and frame ground.” |
755 |
BUCKET WT |
Bucket Weight |
49 |
Calculated |
“The weight of the loader bucket payload. The lift cylinder pressure and lift arm position are used to calculate this value.” |
759 |
HYD OIL PRES |
Hydraulic Oil Pressure |
49 |
PWM |
“The oil pressure in the outlet line of the hydraulic oil pump. The sensor that measures this pressure sends a pulse width varying signal to an ECM depending on the hydraulic oil pump outlet line pressure. The ECM then uses this signal to calculate the hydraulic oil pressure.” |
778 |
ETHER INJECT SW |
Ether Injection Switch |
36 |
Switch |
“The position of the ether injection switch in the cab. This is the switch which the operator uses to manually inject ether for starting. The switch is either OFF or ON (manual injection).” |
779 |
AESC |
Automatic Engine Speed Control |
36 |
Switch |
“The status of the AESC pressure switch. If the engine ECM receives a signal from AESC pressure switch notifying that the hydraulics are being used, then no action is taken. But, if the hydraulics are not being used, the engine ECM idles the engine down to a specified speed to save fuel and reduce engine wear. As soon as the hydraulics begin to be used again, the engine speed is again elevated. AESC state is either ON or OFF.” |
780 |
START RELAY |
Start Relay |
51 |
Switch |
“The status of the start relay. When the engine is cranking, the start relay is engaged.” |
781 |
KEY START SW |
Key Start Switch |
51 |
Switch |
“The status of the key start switch. The status is either ON, OFF or CRANK.” |
782 |
AESC ENABL SW |
Automatic Engine Speed Control Enable Switch |
36/49 |
Switch |
“The status (ACTIVE or INACTIVE) of the Engine Seed Control Automatic Enable switch.” |
783 |
AESC CTRL LINE |
Automatic Engine Speed Control Line |
36/39 |
Switch |
“The status of the AESC output line from the engine ECM.” |
785 |
PAYLOAD SW |
Payload Switch |
39 |
Switch |
“The status of the payload store switch. The switch is normally in the open position. When the switch is pressed, a grounded signal is received, telling VIMS to store the payload data that has been collected since the last store and to clear the present payload data. The switch is either ON or OFF.” |
786 |
HOIST OVER CTR |
Hoist Over center |
87 |
Calculated |
“The status of the hoist overrunning load control. This indicates when the ECM is trying to control the body so an overrunning load will not damage the machine.” |
787 |
HOIST POS CC |
Hoist Lever Position from Chassis Control |
87 |
Analog |
“Used to read the hoist lever mode and the mode drive command percentage. The drive percentage, used by the RAISE, FLOAT, and LOWER modes, indicates the position of the lever within the range of travel for the particular mode.” |
788 |
HOIST STATUS CC |
Hoist Status from Chassis Control |
87 |
Analog |
“Used to read the actual hoist output status and drive command percentage. The drive percentage, used by the RAISE, FLOAT, LOWER and SNUB modes, indicates the position of the lever within the range of travel for the particular mode. ” |
790 |
ATMOS PRES |
Atmospheric Pressure |
36 |
Analog |
“The atmospheric (barometric) pressure on the outside of the machine. The atmospheric pressure sensor sends to the engine ECM a voltage that varies as the pressure changes. The engine ECM then calculates the pressure according to the voltage that is received.” |
791 |
AMB AIR TEMP ` |
Ambient Air Temperature |
49 |
PWM |
“The temperature of the air outside the machine. VIMS receives a signal that changes in pulse width as the outside or ambient air temperature changes. VIMS then uses the pulse width that it receives to determine the ambient air temperature.” |
792 |
MACHINE PITCH |
Machine Pitch |
49 |
Calculated |
“This is calculated from the four machine suspension cylinder pressures. VIMS takes the sum of the two front suspension cylinder pressures minus the sum of the two rear suspension cylinder pressures.” |
793 |
MACHINE RACK |
Machine Rack |
49 |
Calculated |
“This is calculated from the four machine suspension cylinder pressures. VIMS takes the sum of the two diagonal suspension cylinder pressures (left front plus right rear or right front plus left rear) minus the sum of the two other diagonal suspension cylinder pressures.” |
794 |
ATMOS PRES F |
Engine Atmospheric Pressure Front |
33 |
Analog |
“The air pressure at the inlet to the intake manifold of the front engine. (see parameter 790)” |
795 |
REEL LUBE SW |
Reel Lube Switch |
49 |
Switch |
“The status of the reel lube switch (ON or OFF). The reel lube switch will turn the lubrication system on to actuate the manual lube reel. This is an alternate lubrication system from the auto lube system. This system overrides the auto lube system. While this switch is on, the auto lube status will be pending.” |
799 |
HOIST STATUS |
Desired Hoist Status |
27 |
Calculated |
“The desired mode and drive percentage of the hoist for operation. The drive percentage, used by the RAISE, FLOAT, and LOWER modes, indicates the desired lever position within the range of travel for the particular mode.” |
800 |
VIMS EVENT LIST |
VIMS Event List |
49 |
Calculated |
“This is a percentage value that represents the amount of memory space (out of the total) that is left for the VIMS Event List.” |
801 |
PAYLOAD DATA |
Payload Data |
49 |
Calculated |
“This is a percentage value that represents the amount of memory space (out of the total) that is left for storing of payload data. This is calculated by VIMS on off highway trucks.” |
802 |
VIMS SNAPSHOT |
VIMS Snapshot |
49 |
Calculated |
“This is a percentage value that represents the amount of memory space (out of the total) that is left for storing of the VIMS Snapshot data (previously named event recorder data). This value will either be 100, 50, or 0 percent. Every time a snapshot is activated (manually or automatically), the VIMS snapshot value should be reduced by 50 percent. This value can only be reset by downloading the VIMS snapshot data.” |
803 |
PAYLOAD MEMORY |
Payload Memory |
49 |
Calculated |
“This is a percentage value that represents the amount of memory space (out of the total) that is left for storing of payload data. This is calculated by VIMS on large wheel loaders.” |
804 |
PWR SHIFT PRES |
Power Shift Pressure |
36 |
PWM |
“The power shift pressure that is used to control the swash plates on the hydraulic oil pumps. The engine ECM receives a signal that changes in pulse width as the power shift pressure changes. The engine ECM then, using the pulse width that it receives, determines the power shift pressure.” |
805 |
VIDS EVENT LIST |
VIDS Event List |
49 |
Calculated |
“This is a percentage value that represents the amount of memory space (out of the total) that is left for the VIDS Event List data.” |
806 |
PWR SHIFT |
Power Shift |
36 |
Calculated |
“The current as a percentage of maximum which is being delivered to the power shift solenoid.” |
849 |
MAX BIAS/SEC |
Maximum BiasPer Second |
49 |
Calculated |
“Used with RAC electronic control module. Load Bias side to side.” |
850 |
MAX PITCH/SEC |
Maximum Pitch Per Second |
49 |
Calculated |
“Used with RAC electronic control module. Pitch = Fore/AFT motion” |
851 |
MAX RACK/SEC |
Maximum Rack Per Second |
49 |
Calculated |
“Used with RAC electronic control module. Rack = twisting motion” |
852 |
CURRENT FELA |
Current FELA |
49 |
Calculated |
“Used with RAC electronic control module.” |
853 |
MOV AVG1 FELA |
Moving Average Number 1 FELA |
49 |
Calculated |
“Used with RAC electronic control module.” |
854 |
MOV AVG2 FELA |
Moving Average Number 2 FELA |
49 |
Calculated |
“Used with RAC electronic control module.” |
855 |
MOV AVG 3 FELA |
Moving Average Number 3 FELA |
49 |
Calculated |
“Used with RAC electronic control module.” |
856 |
RUN AVG FELA |
Running Average FELA |
49 |
Calculated |
“Used with RAC electronic control module.” |
857 |
CUM FELA UPD |
Cumulative FELA Update |
49 |
Calculated |
“Used with RAC electronic control module.” |
860 |
MANUAL EREC |
Manual Event Recorder |
49 |
Switch |
“The status of the manual event recorder (OFF or RECORDING).” |
862 |
CUR R FELA |
Current Rear FELA |
87 |
Calculated |
“Used with Chassis electronic control module.” |
863 |
MOV AVG1 R FELA |
Moving Average Number 1 Rear FELA |
87 |
Calculated |
“Used with Chassis electronic control module.” |
864 |
MOV AVG3 R FELA |
Moving Average Number 3 Rear FELA |
87 |
Calculated |
“Used with Chassis electronic control module.” |
865 |
MOV AVG5 R FELA |
Moving Average Number 5 Rear FELA |
87 |
Calculated |
“Used with Chassis electronic control module.” |
866 |
RUN AVG R FELA |
Running Average Rear FELA |
87 |
Calculated |
“Used with Chassis electronic control module.” |
876 |
EXH TEMP DEV LTF |
Exhaust Temperature Deviation Left Front |
49 |
Calculated |
“The difference between left front exhaust and the three remaining exhaust banks.” |
877 |
EXH TEMP DEV LTR |
Exhaust Temperature Deviation Left Rear |
49 |
Calculated |
“The difference between left rear exhaust and the three remaining exhaust banks.” |
878 |
EXH TEMP DEV RTF |
Exhaust Temperature Deviation Right Front |
49 |
calculated |
“The difference between right front exhaust and the three remaining exhaust banks.” |
879 |
EXH TEMP DEV RTR |
Exhaust Temperature Deviation Right Rear |
49 |
Calculated |
“The difference between right rear exhaust and the three remaining exhaust banks.” |
900 |
LOADING TIME |
Loading Time |
49 |
Calculated |
“The total time that the machine has spent loading in a given payload cycle.” |
901 |
STOP EMPTY TIME |
Stopped Empty Time |
49 |
Calculated |
“The total time that the machine has been stopped while empty in a given payload cycle.” |
902 |
TRVL EMPTY TIME |
Travel Empty Time |
49 |
Calculated |
“The total time that the machine has been traveling while empty in a given payload cycle.” |
903 |
STOP LOADED TIME |
Stop Loaded Time |
49 |
Calculated |
“The total time that the machine has been stopped while loaded in a given payload cycle.” |
904 |
TRVL LOADED TIME |
Travel Loaded Time |
49 |
Calculated |
“The total amount of time that a machine has been traveling while loaded in a given payload cycle.” |
905 |
THROTTL LCK SPD |
Throttle Lock Speed |
36 |
Calculated |
“The speed that the operator has set as the throttle lock speed with the throttle lock set switch. This is only valid if the throttle lock ON/OFF switch is in the on position.” |
907 |
LOW OIL PRES |
Low Oil Pressure |
36 |
Switch |
“Notifies VIMS of low engine oil pressure. With low pressure, the switch would be open to ground. In normal operation, the switch is closed to ground.” |
910 |
LT FNL DRV CHIP |
Left Final Drive Chip Detector Level |
49 |
Switch |
“This switch notifies VIMS if chips have been detected in the left final drive. As metal chips collect on the magnetic contacts of the switch, a short circuit is made from one terminal to the other causing a closed circuit to ground. During normal operation, the switch is in the open position. The switch is considered closed when the resistance between the two switch terminals is between zero and approximately 2K ohms. ” |
912 |
RT FNL DR CHIP |
Right Final Drive Chip Detector Level |
49 |
Switch |
“This switch notifies VIMS if chips have been detected in the right final drive. As metal chips collect on the magnetic contacts of the switch, a short circuit is made from one terminal to the other causing a closed circuit to ground. During normal operation, the switch is in the open position. The switch is considered closed when the resistance between the two switch terminals is between zero and approximately 2K ohms. ” |
913 |
LT FNL DRV TEMP |
Left Final Drive Oil Temperature |
49 |
PWM |
“The temperature in the left final drive.” |
914 |
RT FNL DRV TEMP |
Right Final Drive Temperature |
49 |
PWM |
The temperature in the right final drive. |
983 |
TKPH F TIRES |
Tons Kilometer Per Hour |
49 |
Calculated |
“This is a calculation of the Front tires temp based on load and distance traveled.” |
984 |
TKPH R TIRES |
Tons Kilometer Per Hour |
49 |
Calculated |
“This is a calculation of the Rear tires temp based on load and distance traveled.” |
7107 |
INJ DISABLD |
Engine Injection Disalbled |
36 |
Calculated |
“The engine status parameter is monitored to see if the injectors have been disabled.” |
7108 |
OIL PRES F SHTDN |
Oil Pressure Front Shutdown Status |
33 |
Calculated |
“This parameter senses if the front engine has been shutdown due to low oil pressure. The engine ECM will turn off the Rear Low Oil Pressure status immediately when the rear engine is shutdown. This parameter looks for a change of state in the low oil pressure status from LO to OK and injection disabled from OFF to ON.” |
7109 |
TRN OIL PRES LO |
Transmission Oil Pressure Low |
116 |
Calculated |
“Monitors the low region of the transmission oil pressure. ” |
7110 |
TRN OIL PRES HI |
Transmission Oil Pressure High |
116 |
Calculated |
“Monitors the region of high transmission oil pressure.” |
7112 |
OIL PRES R SHUTDN |
Oil Pressure Rear Shutdown Status |
34 |
Calculated |
“This parameter senses if the rear engine has been shutdown due to low oil pressure. The engine ECM will turn off the Rear Low Oil Pressure status immediately when the rear engine is shutdown. This parameter looks for a change of state in the low oil pressure status from LO to OK and injection disabled from OFF to ON.” |
7701 |
RETRDR LVR |
Retarder Lever Position |
116 |
PWM |
“Reads the position of the auto retarder lever. This signal is a percentage of full travel.” |
7738 |
AUTO RETRDR SW |
Automatic Retarder Pressure Switch Status |
116 |
Switch |
“Shows the state of the ARC pressure switch. The ARC pressure is either HI or LO.” |


