Diagnostic Trouble Codes
SMCS - 1900
Cross-Reference Information for Diagnostic Codes
Table 1 is a list of the diagnostic codes for the engine. The diagnostic codes are cross-referenced with the appropriate procedure that can be used to troubleshoot the code.
Further explanations of diagnostic codes are explained after Table 1.
Portions of this material are reprinted with permission from SAE J1939DA_201607© 2016 SAE International. SAE International is not responsible for any use or translation of this material, in whole or in part. Please contact SAE International to obtain a complete copy of SAE J1939DA_201607, the official definitive source of this standard.
Table 1
Cross-Reference from Diagnostic Trouble Codes to Functional Test or Procedure |
||
J1939 Code and Description |
CDL Code and Description |
Troubleshooting Procedure |
52-3 Engine Intercooler Temperature : Voltage Above Normal |
279-3 Aftercooler Coolant Temperature Sensor (Front) : Voltage Above Normal |
Troubleshooting, "Sensor Signal (Analog, Passive) - Test" |
52-4 Engine Intercooler Temperature : Voltage Below Normal |
279-4 Aftercooler Coolant Temperature Sensor (Front) : Voltage Below Normal |
Troubleshooting, "Sensor Signal (Analog, Passive) - Test" |
91-3 Accelerator Pedal Position #1 : Voltage Above Normal |
91-3 Throttle Position Sensor : Voltage Above Normal |
Troubleshooting, "Speed Control - Test" |
91-4 Accelerator Pedal Position #1 : Voltage Below Normal |
91-4 Throttle Position Sensor : Voltage Below Normal |
Troubleshooting, "Speed Control - Test" |
91-8 Accelerator Pedal Position #1 : Abnormal Frequency, Pulse Width, or Period |
91-8 Throttle Position Sensor : Abnormal Frequency, Pulse Width, or Period |
Troubleshooting, "Speed Control - Test" |
94-3 Engine Fuel Delivery Pressure : Voltage Above Normal |
289-3 Fuel Pressure Sensor - Before Fuel Filter : Voltage Above Normal |
Troubleshooting, "Sensor Signal (Analog, Active) - Test" |
94-4 Engine Fuel Delivery Pressure : Voltage Below Normal |
289-4 Fuel Pressure Sensor - Before Fuel Filter : Voltage Below Normal |
Troubleshooting, "Sensor Signal (Analog, Active) - Test" |
95-2 Engine Fuel Filter Differential Pressure : Erratic, Intermittent, or Incorrect |
95-2 Fuel Filter Differential Pressure Sensor : Erratic, Intermittent, or Incorrect |
The filtered fuel pressure is greater than the unfiltered fuel pressure. Ensure that the sensor connectors are connected to the correct sensors. If an electrical problem with a sensor is suspected, refer to Troubleshooting, "Sensor Signal (Analog, Active) - Test" for information that is related to troubleshooting an electrical problem with the fuel pressure sensors. |
99-2 Engine Oil Filter Differential Pressure : Erratic, Intermittent, or Incorrect |
99-2 Engine Oil Filter Differential Pressure Sensor : Erratic, Intermittent, or Incorrect |
The filtered oil pressure is greater than the unfiltered oil pressure. Ensure that the sensor connectors are connected to the correct sensors. If an electrical problem with a sensor is suspected, refer to Troubleshooting, "Sensor Signal (Analog, Active) - Test" for information that is related to troubleshooting an electrical problem with the oil pressure sensors. |
100-3 Engine Oil Pressure : Voltage Above Normal |
100-3 Engine Oil Pressure Sensor : Voltage Above Normal |
Troubleshooting, "Sensor Signal (Analog, Active) - Test" |
100-4 Engine Oil Pressure : Voltage Below Normal |
100-4 Engine Oil Pressure Sensor : Voltage Below Normal |
Troubleshooting, "Sensor Signal (Analog, Active) - Test" |
100-21 Engine Oil Pressure : Data Drifted Low |
100-21 Engine Oil Pressure Sensor : Data Drifted Low |
Troubleshooting, "Sensor Supply - Test" |
101-3 Engine Crankcase Pressure : Voltage Above Normal |
101-3 Crankcase Air Pressure Sensor : Voltage Above Normal |
Troubleshooting, "Sensor Signal (Analog, Active) - Test" |
101-4 Engine Crankcase Pressure : Voltage Below Normal |
101-4 Crankcase Air Pressure Sensor : Voltage Below Normal |
Troubleshooting, "Sensor Signal (Analog, Active) - Test" |
101-13 Engine Crankcase Pressure : Out of Calibration |
101-13 Crankcase Air Pressure Sensor : Out of Calibration |
Troubleshooting, "Sensor Calibration Required - Test" |
101-21 Engine Crankcase Pressure : Data Drifted Low |
101-21 Crankcase Air Pressure Sensor : Data Drifted Low |
Troubleshooting, "Sensor Supply - Test" |
105-3 Engine Intake Manifold #1 Temperature : Voltage Above Normal |
172-3 Intake Manifold Air Temperature Sensor : Voltage Above Normal |
Troubleshooting, "Sensor Signal (Analog, Passive) - Test" |
105-4 Engine Intake Manifold #1 Temperature : Voltage Below Normal |
172-4 Intake Manifold Air Temperature Sensor : Voltage Below Normal |
Troubleshooting, "Sensor Signal (Analog, Passive) - Test" |
108-3 Barometric Pressure : Voltage Above Normal |
3528-3 Barometric Pressure Sensor : Voltage Above Normal |
Troubleshooting, "Sensor Signal (Analog, Active) - Test" |
108-4 Barometric Pressure : Voltage Below Normal |
3528-4 Barometric Pressure Sensor : Voltage Below Normal |
Troubleshooting, "Sensor Signal (Analog, Active) - Test" |
108-21 Barometric Pressure : Data Drifted Low |
3528-21 Barometric Pressure Sensor : Data Drifted Low |
Troubleshooting, "Sensor Supply - Test" |
109-3 Engine Coolant Pressure : Voltage Above Normal |
2302-3 Engine Coolant Pump Outlet Pressure Sensor : Voltage Above Normal |
Troubleshooting, "Sensor Signal (Analog, Active) - Test" |
109-4 Engine Coolant Pressure : Voltage Below Normal |
2302-4 Engine Coolant Pump Outlet Pressure Sensor : Voltage Below Normal |
Troubleshooting, "Sensor Signal (Analog, Active) - Test" |
110-3 Engine Coolant Temperature : Voltage Above Normal |
110-3 Engine Coolant Temperature Sensor : Voltage Above Normal |
Troubleshooting, "Sensor Signal (Analog, Passive) - Test" |
110-4 Engine Coolant Temperature : Voltage Below Normal |
110-4 Engine Coolant Temperature Sensor : Voltage Below Normal |
Troubleshooting, "Sensor Signal (Analog, Passive) - Test" |
168-3 Battery Potential / Power Input #1 : Voltage Above Normal |
168-3 Electrical System Voltage : Voltage Above Normal |
Troubleshooting, "Electrical Power Supply - Test" |
168-4 Battery Potential / Power Input #1 : Voltage Below Normal |
168-4 Electrical System Voltage : Voltage Below Normal |
Troubleshooting, "Electrical Power Supply - Test" |
190-8 Engine Speed : Abnormal Frequency, Pulse Width, or Period |
190-8 Engine Speed Sensor : Abnormal Frequency, Pulse Width, or Period |
Troubleshooting, "Speed/Timing - Test" |
626-5 Engine Start Enable Device 1 : Current Below Normal |
2417-5 Ether Injection Control Solenoid : Current Below Normal |
Troubleshooting, "Ether Starting Aid - Test" |
626-6 Engine Start Enable Device 1 : Current Above Normal |
2417-6 Ether Injection Control Solenoid : Current Above Normal |
Troubleshooting, "Ether Starting Aid - Test" |
630-2 Calibration Memory : Erratic, Intermittent, or Incorrect |
268-2 Programmed Parameter Fault : Erratic, Intermittent, or Incorrect |
Troubleshooting, "Configuration Parameters" |
631-2 Calibration Module : Erratic, Intermittent, or Incorrect |
253-2 Personality Module : Erratic, Intermittent, or Incorrect |
Troubleshooting, "ECM Software - Install" |
637-11 Engine Timing Sensor : Other Failure Mode |
261-11 Engine Timing Offset fault |
The ECM has detected the crankshaft and camshaft position to be out of time. Refer to Testing and Adjusting, "Camshaft Timing". |
651-5 Engine Injector Cylinder #01 : Current Below Normal |
1-5 Cylinder #1 Injector : Current Below Normal |
Troubleshooting, "Injector Solenoid - Test" |
651-6 Engine Injector Cylinder #01 : Current Above Normal |
1-6 Cylinder #1 Injector : Current Above Normal |
Troubleshooting, "Injector Solenoid - Test" |
652-5 Engine Injector Cylinder #02 : Current Below Normal |
2-5 Cylinder #2 Injector : Current Below Normal |
Troubleshooting, "Injector Solenoid - Test" |
652-6 Engine Injector Cylinder #02 : Current Above Normal |
2-6 Cylinder #2 Injector : Current Above Normal |
Troubleshooting, "Injector Solenoid - Test" |
653-5 Engine Injector Cylinder #03 : Current Below Normal |
3-5 Cylinder #3 Injector : Current Below Normal |
Troubleshooting, "Injector Solenoid - Test" |
653-6 Engine Injector Cylinder #03 : Current Above Normal |
3-6 Cylinder #3 Injector : Current Above Normal |
Troubleshooting, "Injector Solenoid - Test" |
654-5 Engine Injector Cylinder #04 : Current Below Normal |
4-5 Cylinder #4 Injector : Current Below Normal |
Troubleshooting, "Injector Solenoid - Test" |
654-6 Engine Injector Cylinder #04 : Current Above Normal |
4-6 Cylinder #4 Injector : Current Above Normal |
Troubleshooting, "Injector Solenoid - Test" |
655-5 Engine Injector Cylinder #05 : Current Below Normal |
5-5 Cylinder #5 Injector : Current Below Normal |
Troubleshooting, "Injector Solenoid - Test" |
655-6 Engine Injector Cylinder #05 : Current Above Normal |
5-6 Cylinder #5 Injector : Current Above Normal |
Troubleshooting, "Injector Solenoid - Test" |
656-5 Engine Injector Cylinder #06 : Current Below Normal |
6-5 Cylinder #6 Injector : Current Below Normal |
Troubleshooting, "Injector Solenoid - Test" |
656-6 Engine Injector Cylinder #06 : Current Above Normal |
6-6 Cylinder #6 Injector : Current Above Normal |
Troubleshooting, "Injector Solenoid - Test" |
657-5 Engine Injector Cylinder #07 : Current Below Normal |
7-5 Cylinder #7 Injector : Current Below Normal |
Troubleshooting, "Injector Solenoid - Test" |
657-6 Engine Injector Cylinder #07 : Current Above Normal |
7-6 Cylinder #7 Injector : Current Above Normal |
Troubleshooting, "Injector Solenoid - Test" |
658-5 Engine Injector Cylinder #08 : Current Below Normal |
8-5 Cylinder #8 Injector : Current Below Normal |
Troubleshooting, "Injector Solenoid - Test" |
658-6 Engine Injector Cylinder #08 : Current Above Normal |
8-6 Cylinder #8 Injector : Current Above Normal |
Troubleshooting, "Injector Solenoid - Test" |
659-5 Engine Injector Cylinder #09 : Current Below Normal |
9-5 Cylinder #9 Injector : Current Below Normal |
Troubleshooting, "Injector Solenoid - Test" |
659-6 Engine Injector Cylinder #09 : Current Above Normal |
9-6 Cylinder #9 Injector : Current Above Normal |
Troubleshooting, "Injector Solenoid - Test" |
660-5 Engine Injector Cylinder #10 : Current Below Normal |
10-5 Cylinder #10 Injector : Current Below Normal |
Troubleshooting, "Injector Solenoid - Test" |
660-6 Engine Injector Cylinder #10 : Current Above Normal |
10-6 Cylinder #10 Injector : Current Above Normal |
Troubleshooting, "Injector Solenoid - Test" |
661-5 Engine Injector Cylinder #11 : Current Below Normal |
11-5 Cylinder #11 Injector : Current Below Normal |
Troubleshooting, "Injector Solenoid - Test" |
661-6 Engine Injector Cylinder #11 : Current Above Normal |
11-6 Cylinder #11 Injector : Current Above Normal |
Troubleshooting, "Injector Solenoid - Test" |
662-5 Engine Injector Cylinder #12 : Current Below Normal |
12-5 Cylinder #12 Injector : Current Below Normal |
Troubleshooting, "Injector Solenoid - Test" |
662-6 Engine Injector Cylinder #12 : Current Above Normal |
12-6 Cylinder #12 Injector : Current Above Normal |
Troubleshooting, "Injector Solenoid - Test" |
663-5 Engine Injector Cylinder #13 : Current Below Normal |
13-5 Cylinder #13 Injector : Current Below Normal |
Troubleshooting, "Injector Solenoid - Test" |
663-6 Engine Injector Cylinder #13 : Current Above Normal |
13-6 Cylinder #13 Injector : Current Above Normal |
Troubleshooting, "Injector Solenoid - Test" |
664-5 Engine Injector Cylinder #14 : Current Below Normal |
14-5 Cylinder #14 Injector : Current Below Normal |
Troubleshooting, "Injector Solenoid - Test" |
664-6 Engine Injector Cylinder #14 : Current Above Normal |
14-6 Cylinder #14 Injector : Current Above Normal |
Troubleshooting, "Injector Solenoid - Test" |
665-5 Engine Injector Cylinder #15 : Current Below Normal |
15-5 Cylinder #15 Injector : Current Below Normal |
Troubleshooting, "Injector Solenoid - Test" |
665-6 Engine Injector Cylinder #15 : Current Above Normal |
15-6 Cylinder #15 Injector : Current Above Normal |
Troubleshooting, "Injector Solenoid - Test" |
666-5 Engine Injector Cylinder #16 : Current Below Normal |
16-5 Cylinder #16 Injector : Current Below Normal |
Troubleshooting, "Injector Solenoid - Test" |
666-6 Engine Injector Cylinder #16 : Current Above Normal |
16-6 Cylinder #16 Injector : Current Above Normal |
Troubleshooting, "Injector Solenoid - Test" |
678-3 ECU 8 VDC Supply : Voltage Above Normal |
41-3 8 VDC Supply : Voltage Above Normal |
Troubleshooting, "Sensor Supply - Test" |
678-4 ECU 8 VDC Supply : Voltage Below Normal |
41-4 8 VDC Supply : Voltage Below Normal |
Troubleshooting, "Sensor Supply - Test" |
723-8 Engine Speed Sensor #2 : Abnormal Frequency, Pulse Width, or Period |
342-8 Secondary Engine Speed Sensor : Abnormal Frequency, Pulse Width, or Period |
Troubleshooting, "Speed/Timing - Test" |
1176-3 Engine Turbocharger #1 Compressor Inlet Pressure : Voltage Above Normal |
2738-3 Turbocharger #1 Compressor Inlet Pressure Sensor : Voltage Above Normal |
Troubleshooting, "Sensor Signal (Analog, Active) - Test" |
1176-4 Engine Turbocharger #1 Compressor Inlet Pressure : Voltage Below Normal |
2738-4 Turbocharger #1 Compressor Inlet Pressure Sensor : Voltage Below Normal |
Troubleshooting, "Sensor Signal (Analog, Active) - Test" |
1177-3 Engine Turbocharger #2 Compressor Inlet Pressure : Voltage Above Normal |
2739-3 Turbocharger #2 Compressor Inlet Pressure Sensor : Voltage Above Normal |
Troubleshooting, "Sensor Signal (Analog, Active) - Test" |
1177-4 Engine Turbocharger #2 Compressor Inlet Pressure : Voltage Below Normal |
2739-4 Turbocharger #2 Compressor Inlet Pressure Sensor : Voltage Below Normal |
Troubleshooting, "Sensor Signal (Analog, Active) - Test" |
1208-3 Engine Pre-filter Oil Pressure : Voltage Above Normal |
542-3 Engine Oil Pressure Sensor - Before Oil Filter : Voltage Above Normal |
Troubleshooting, "Sensor Signal (Analog, Active) - Test" |
1208-4 Engine Pre-filter Oil Pressure : Voltage Below Normal |
542-4 Engine Oil Pressure Sensor - Before Oil Filter : Voltage Below Normal |
Troubleshooting, "Sensor Signal (Analog, Active) - Test" |
1208-21 Engine Pre-filter Oil Pressure : Data Drifted Low |
542-21 Engine Oil Pressure Sensor - Before Oil Filter : Data Drifted Low |
Troubleshooting, "Sensor Supply - Test" |
2433-3 Engine Exhaust Manifold Bank #2 Temperature #1 : Voltage Above Normal |
828-3 Right Exhaust Temperature Sensor : Voltage Above Normal |
Troubleshooting, "Sensor Signal (PWM) - Test" |
2433-4 Engine Exhaust Manifold Bank #2 Temperature #1 : Voltage Below Normal |
828-4 Right Exhaust Temperature Sensor : Voltage Below Normal |
Troubleshooting, "Sensor Signal (PWM) - Test" |
2433-8 Engine Exhaust Manifold Bank #2 Temperature #1 : Abnormal Frequency, Pulse Width, or Period |
828-8 Right Exhaust Temperature Sensor : Abnormal Frequency, Pulse Width, or Period |
Troubleshooting, "Sensor Signal (PWM) - Test" |
2434-3 Engine Exhaust Manifold Bank #1 Temperature #1 : Voltage Above Normal |
827-3 Left Exhaust Temperature Sensor : Voltage Above Normal |
Troubleshooting, "Sensor Signal (PWM) - Test" |
2434-4 Engine Exhaust Manifold Bank #1 Temperature #1 : Voltage Below Normal |
827-4 Left Exhaust Temperature Sensor : Voltage Below Normal |
Troubleshooting, "Sensor Signal (PWM) - Test" |
2434-8 Engine Exhaust Manifold Bank #1 Temperature #1 : Abnormal Frequency, Pulse Width, or Period |
827-8 Left Exhaust Temperature Sensor : Abnormal Frequency, Pulse Width, or Period |
Troubleshooting, "Sensor Signal (PWM) - Test" |
3509-3 Sensor Supply Voltage 1 : Voltage Above Normal |
262-3 5 V Sensor DC Power Supply : Voltage Above Normal |
Troubleshooting, "Sensor Supply - Test" |
3509-4 Sensor Supply Voltage 1 : Voltage Below Normal |
262-4 5 V Sensor DC Power Supply : Voltage Below Normal |
Troubleshooting, "Sensor Supply - Test" |
3510-3 Sensor Supply Voltage 2 : Voltage Above Normal |
2131-3 5 V Sensor DC Power Supply #2 : Voltage Above Normal |
Troubleshooting, "Sensor Supply - Test" |
3510-4 Sensor Supply Voltage 2 : Voltage Below Normal |
2131-4 5 V Sensor DC Power Supply #2 : Voltage Below Normal |
Troubleshooting, "Sensor Supply - Test" |
3563-3 Engine Intake Manifold #1 Absolute Pressure : Voltage Above Normal |
1785-3 Intake Manifold Pressure Sensor : Voltage Above Normal |
Troubleshooting, "Sensor Signal (Analog, Active) - Test" |
3563-4 Engine Intake Manifold #1 Absolute Pressure : Voltage Below Normal |
1785-4 Intake Manifold Pressure Sensor : Voltage Below Normal |
Troubleshooting, "Sensor Signal (Analog, Active) - Test" |
3563-13 Engine Intake Manifold #1 Absolute Pressure : Out of Calibration |
1785-13 Intake Manifold Pressure Sensor : Out of Calibration |
Troubleshooting, "Sensor Calibration Required - Test" |
3563-21 Engine Intake Manifold #1 Absolute Pressure : Data Drifted Low |
1785-21 Intake Manifold Pressure Sensor : Data Drifted Low |
Troubleshooting, "Sensor Calibration Required - Test" |
4210-5 Engine Pre-lube Drive : Current Below Normal |
338-5 Engine Pre-Lube Pump Relay : Current Below Normal |
Troubleshooting, "Solenoid Valve - Test" |
4210-6 Engine Pre-lube Drive : Current Above Normal |
338-6 Engine Pre-Lube Pump Relay : Current Above Normal |
Troubleshooting, "Solenoid Valve - Test" |
4215-3 Ground-Level Shutdown Activated : Voltage Above Normal |
267-3 Remote Shutdown Input : Voltage Above Normal |
Troubleshooting, "Shutdown (Ground Level) - Test" |
4215-4 Ground-Level Shutdown Activated : Voltage Below Normal |
267-4 Remote Shutdown Input : Voltage Below Normal |
Troubleshooting, "Shutdown (Ground Level) - Test" |
5578-21 Engine Fuel Delivery Absolute Pressure : Data Drifted Low |
289-21 Fuel Pressure Sensor - Before Fuel Filter : Data Drifted Low |
Troubleshooting, "Sensor Supply - Test" |
5579-3 Engine Filtered Fuel Delivery Pressure : Voltage Above Normal |
460-3 Fuel Pressure Sensor - After Fuel Filter : Voltage Above Normal |
Troubleshooting, "Sensor Signal (Analog, Active) - Test" |
5579-4 Engine Filtered Fuel Delivery Pressure : Voltage Below Normal |
460-4 Fuel Pressure Sensor - After Fuel Filter : Voltage Below Normal |
Troubleshooting, "Sensor Signal (Analog, Active) - Test" |
5580-21 Engine Filtered Fuel Delivery Absolute Pressure : Data Drifted Low |
460-21 Fuel Pressure Sensor - After Fuel Filter : Data Drifted Low |
Troubleshooting, "Sensor Supply - Test" |
N/A |
296-9 Transmission Control : Abnormal Update Rate |
Troubleshooting, "Data Link - Test" |
N/A |
296-14 Transmission Control : Special Instruction |
Troubleshooting, "Data Link - Test" |
N/A |
545-5 Ether Start Relay open/short to +batt |
Troubleshooting, "Ether Starting Aid - Test" |
N/A |
545-6 Ether Start Relay short to ground |
Troubleshooting, "Ether Starting Aid - Test" |
N/A |
800-9 VIMS Main Module : Abnormal Update Rate |
Troubleshooting, "Data Link - Test" |
N/A |
800-14 VIMS Main Module : Special Instruction |
Troubleshooting, "Data Link - Test" |
N/A |
829-3 Rear Aftercooler Coolant Temperature Sensor : Voltage Above Normal |
Troubleshooting, "Sensor Signal (Analog, Passive) - Test" |
N/A |
829-4 Rear Aftercooler Coolant Temperature Sensor : Voltage Below Normal |
Troubleshooting, "Sensor Signal (Analog, Passive) - Test" |
N/A |
2271-5 Engine Oil Renewal System Actuation Solenoid : Current Below Normal |
Troubleshooting, "Solenoid Valve - Test" |
N/A |
2271-6 Engine Oil Renewal System Actuation Solenoid : Current Above Normal |
Troubleshooting, "Solenoid Valve - Test" |
Diagnostic Codes
Diagnostic codes alert the operator that a problem in the electronic system has been detected. Diagnostic codes are also used by the service technician to identify the nature of the problem. Cat®Electronic Technician (ET) is a software program that runs on a personal computer. The software can be used by the service technician to view the diagnostic code information for an ECM. The diagnostic code will be displayed as a two-element code. The following terms describe the elements of the code:
Suspect Parameter Number (SPN) - The SPN is a code which is assigned to each component to identify data.
Failure Mode Identifier (FMI) - The FMI indicates the type of failure.
Refer to Table 1 for a complete list of the diagnostic codes and the appropriate troubleshooting procedure.
Note: Do not confuse diagnostic codes with event codes. Event codes alert the operator that an abnormal operating condition such as low oil pressure or high coolant temperature has been detected. If an event code is active, refer to Troubleshooting, "Event Codes".
Active Diagnostic Codes
An active diagnostic code represents a problem with the electronic control system. Correct the problem as soon as possible.
When the ECM generates an active diagnostic code. The "Active Alarm" indicator ("Control Alarm Status" on Cat ET) is activated to alert the operator. If the condition that generated the code is momentary, the message disappears from the list of active diagnostic codes. The diagnostic code becomes logged.
Logged Diagnostic Codes
When the ECM generates a diagnostic code, the ECM logs the code in permanent memory. The ECM has an internal diagnostic clock. Each ECM will record the following information when a code is generated:
•The hour of the first occurrence of the code
•The hour of the last occurrence of the code
•The number of occurrences of the code
This information is a valuable indicator for troubleshooting intermittent problems.
A code is cleared from memory when one of the following conditions occur:
•The service technician manually clears the code.
•The code does not recur for 100 hours.
•A new code is logged and there are already ten codes in memory. In this case, the oldest code is cleared.
Some diagnostic codes may be easily triggered. Some diagnostic codes may log occurrences that did not result in complaints. The most likely cause of an intermittent problem is a faulty connection or damaged wiring. The next likely cause is a component failure. The least likely cause is the failure of an electronic module. Diagnostic codes that are logged repeatedly may indicate a problem that needs special investigation.
Note: Always clear logged diagnostic codes after investigating and correcting the problem which generated the code.
Event Codes
SMCS - 1900
Engine Monitoring
The Electronic Control Module (ECM) monitors the operating parameters of the engine. The ECM will generate an event code if a specific engine parameter exceeds an acceptable range that is defined by the engine monitoring system. For information on the engine monitoring system, refer to Troubleshooting, "Engine Monitoring System".
Cross-Reference Information for Event Codes
Event codes are generated when abnormal operating conditions exist. Table 1 is a list of the event codes for the engine. The event codes are cross-referenced with the appropriate procedure that can be used to troubleshoot the code.
Table 1
Cross-Reference from Diagnostic Trouble Codes to Functional Test or Procedure |
||
J1939 Code and Description |
CDL Code and Description |
Troubleshooting Procedure |
94-16 Engine Fuel Delivery Pressure : High - moderate severity (2) |
E1218 (2) High Unfiltered Fuel Pressure |
Troubleshooting, "Fuel Pressure Is High" |
95-0 Engine Fuel Filter Differential Pressure : High - most severe (3) |
E390 (3) Fuel Filter Restriction |
Troubleshooting, "Fuel Filter Is Restricted" |
95-15 Engine Fuel Filter Differential Pressure : High - least severe (1) |
E390 (1) Fuel Filter Restriction |
Troubleshooting, "Fuel Filter Is Restricted" |
95-16 Engine Fuel Filter Differential Pressure : High - moderate severity (2) |
E390 (2) Fuel Filter Restriction |
Troubleshooting, "Fuel Filter Is Restricted" |
98-1 Engine Oil Level : Low - most severe (3) |
E171 (3) Low Engine Oil Level |
Troubleshooting, "Oil Level Is Low" |
98-18 Engine Oil Level : Low - moderate severity (2) |
E171 (2) Low Engine Oil Level |
Troubleshooting, "Oil Level Is Low" |
99-0 Engine Oil Filter Differential Pressure : High - most severe (3) |
E73 (3) High Oil Filter Differential Pressure |
Troubleshooting, "Oil Filter Differential Pressure Problem" |
99-15 Engine Oil Filter Differential Pressure : High - least severe (1) |
E73 (1) High Oil Filter Differential Pressure |
Troubleshooting, "Oil Filter Differential Pressure Problem" |
99-16 Engine Oil Filter Differential Pressure : High - moderate severity (2) |
E73 (2) High Oil Filter Differential Pressure |
Troubleshooting, "Oil Filter Differential Pressure Problem" |
100-1 Engine Oil Pressure : Low - most severe (3) |
E360 (3) Low Engine Oil Pressure |
Troubleshooting, "Oil Pressure Is Low" |
100-14 Engine Oil Pressure : Special Instruction |
E233 (1) Low Engine Pre-Lube Pressure |
The Electronic Control Module (ECM) has detected the oil pressure did not go above a threshold during the prelube cycle. |
100-17 Engine Oil Pressure : Low - least severe (1) |
E360 (1) Low Engine Oil Pressure |
Troubleshooting, "Oil Pressure Is Low" |
100-18 Engine Oil Pressure : Low - moderate severity (2) |
E360 (2) Low Engine Oil Pressure |
Troubleshooting, "Oil Pressure Is Low" |
101-0 Engine Crankcase Pressure : High - most severe (3) |
E1036 (3) High Crankcase Pressure |
Troubleshooting, "Crankcase Pressure Is High" |
101-15 Engine Crankcase Pressure : High - least severe (1) |
E1036 (1) High Crankcase Pressure |
Troubleshooting, "Crankcase Pressure Is High" |
101-16 Engine Crankcase Pressure : High - moderate severity (2) |
E1036 (2) High Crankcase Pressure |
Troubleshooting, "Crankcase Pressure Is High" |
105-0 Engine Intake Manifold #1 Temperature : High - most severe (3) |
E539 (3) High Intake Manifold Air Temperature |
Troubleshooting, "Intake Manifold Air Temperature Is High" |
105-15 Engine Intake Manifold #1 Temperature : High - least severe (1) |
E539 (1) High Intake Manifold Air Temperature |
Troubleshooting, "Intake Manifold Air Temperature Is High" |
105-16 Engine Intake Manifold #1 Temperature : High - moderate severity (2) |
E539 (2) High Intake Manifold Air Temperature |
Troubleshooting, "Intake Manifold Air Temperature Is High" |
107-15 Engine Air Filter 1 Differential Pressure : High - least severe (1) |
E583 (1) High Engine Air Filter #1 Differential Pressure |
Troubleshooting, "Inlet Air Is Restricted" |
107-16 Engine Air Filter 1 Differential Pressure : High - moderate severity (2) |
E583 (2) High Engine Air Filter #1 Differential Pressure |
Troubleshooting, "Inlet Air Is Restricted" |
109-1 Engine Coolant Pressure : Low - most severe (3) |
E2112 (3) Low Engine Coolant Pressure |
Troubleshooting, "Coolant Pressure Is Low" |
109-17 Engine Coolant Pressure : Low - least severe (1) |
E2112 (1) Low Engine Coolant Pressure |
Troubleshooting, "Coolant Pressure Is Low" |
109-18 Engine Coolant Pressure : Low - moderate severity (2) |
E2112 (2) Low Engine Coolant Pressure |
Troubleshooting, "Coolant Pressure Is Low" |
110-0 Engine Coolant Temperature : High - most severe (3) |
E361 (3) High Engine Coolant Temperature |
Troubleshooting, "Coolant Temperature Is High" |
110-1 Engine Coolant Temperature : Low - most severe (3) |
E199 (3) Low Coolant Temperature |
Troubleshooting, "Coolant Temperature Is Low" |
110-15 Engine Coolant Temperature : High - least severe (1) |
E361 (1) High Engine Coolant Temperature |
Troubleshooting, "Coolant Temperature Is High" |
110-16 Engine Coolant Temperature : High - moderate severity (2) |
E361 (2) High Engine Coolant Temperature |
Troubleshooting, "Coolant Temperature Is High" |
110-17 Engine Coolant Temperature : Low - least severe (1) |
E199 (1) Low Coolant Temperature |
Troubleshooting, "Coolant Temperature Is Low" |
110-18 Engine Coolant Temperature : Low - moderate severity (2) |
E199 (2) Low Coolant Temperature |
Troubleshooting, "Coolant Temperature Is Low" |
190-0 Engine Speed : High - most severe (3) |
E362 (3) Engine Overspeed |
Troubleshooting, "Engine Overspeeds" |
190-15 Engine Speed : High - least severe (1) |
E362 (1) Engine Overspeed |
Troubleshooting, "Engine Overspeeds" |
2433-0 Engine Exhaust Manifold Bank #2 Temperature #1 : High - most severe (3) |
E321 (3) High Right Exhaust Temperature |
Troubleshooting, "Exhaust Differential Temperature is High" |
2433-15 Engine Exhaust Manifold Bank #2 Temperature #1 : High - least severe (1) |
E321 (1) High Right Exhaust Temperature |
Troubleshooting, "Exhaust Differential Temperature is High" |
2433-16 Engine Exhaust Manifold Bank #2 Temperature #1 : High - moderate severity (2) |
E321 (2) High Right Exhaust Temperature |
Troubleshooting, "Exhaust Differential Temperature is High" |
2434-0 Engine Exhaust Manifold Bank #1 Temperature #1 : High - most severe (3) |
E322 (3) High Left Exhaust Temperature |
Troubleshooting, "Exhaust Differential Temperature is High" |
2434-15 Engine Exhaust Manifold Bank #1 Temperature #1 : High - least severe (1) |
E322 (1) High Left Exhaust Temperature |
Troubleshooting, "Exhaust Differential Temperature is High" |
2434-16 Engine Exhaust Manifold Bank #1 Temperature #1 : High - moderate severity (2) |
E322 (2) High Left Exhaust Temperature |
Troubleshooting, "Exhaust Differential Temperature is High" |
2809-15 Engine Air Filter 2 Differential Pressure : High - least severe (1) |
E584 (1) High Engine Air Filter #2 Differential Pressure |
Troubleshooting, "Inlet Air Is Restricted" |
2809-16 Engine Air Filter 2 Differential Pressure : High - moderate severity (2) |
E584 (2) High Engine Air Filter #2 Differential Pressure |
Troubleshooting, "Inlet Air Is Restricted" |
4209-31 Engine Crank Without Pre-lube |
E98 (1) Engine Pre-lube Override |
Quickstart is initiated by turning the key switch to the START position directly followed by turning the key to the OFF position and then within one second turning the key to the START position again. When a Quickstart was detected by the engine ECM, a 4209-31 Engine Crank Without Pre-lube or E98 (1) Engine Pre-lube Override will be logged by the engine ECM. |
4215-31 Ground-Level Shutdown Activated |
E678 (1) Ground Level Shutdown |
Troubleshooting, "Shutdown (Ground Level) - Test" |
5580-17 Engine Filtered Fuel Delivery Absolute Pressure : Low - least severe (1) |
E198 (1) Low Fuel Pressure |
Troubleshooting, "Fuel Pressure Is Low" |
5580-18 Engine Filtered Fuel Delivery Absolute Pressure : Low - moderate severity (2) |
E198 (2) Low Fuel Pressure |
Troubleshooting, "Fuel Pressure Is Low" |
N/A |
E265 (1) User Defined Shutdown |
Troubleshooting, "Engine Shutdown Occurrence" |
N/A |
E278 (1) High Exhaust Differential Temperature |
Troubleshooting, "Turbocharger Turbine Temperature Is High" |
N/A |
E278 (2) High Exhaust Differential Temperature |
Troubleshooting, "Turbocharger Turbine Temperature Is High" |
N/A |
E278 (3) High Exhaust Differential Temperature |
Troubleshooting, "Turbocharger Turbine Temperature Is High" |
N/A |
E540 (1) Low Engine Oil Refill Tank Level |
Troubleshooting, "Oil Level - Test" |
N/A |
E563 (3) Low Engine Coolant Flow |
Troubleshooting, "Coolant Pressure Is Low" |
Active Event Codes
An active event code represents a problem with engine operation. Correct the problem as soon as possible.
Active event codes are listed in ascending numerical order. The code with the lowest number is listed first.
Illustration 1 is an example of the operating range of a sensor.
Illustration 1 |
g01365757 |
Example of the typical operating range of a sensor (1) This area represents the normal operating range of the engine parameter. (2) In these areas, the engine is operating in an unsafe operating range of the monitored parameter. An event code will be generated for the monitored parameter. The sensor circuit does not have an electronic problem. (3) In these areas, the signal from the sensor is outside of the operating range of the sensor. The sensor circuit has an electronic problem. A diagnostic code will be generated for the sensor circuit. Refer to Troubleshooting, "Diagnostic Trouble Codes" for additional information on diagnostic codes. |
|
Logged Event Codes
When the ECM generates an event code, the ECM may log the event code in permanent memory. The ECM has an internal diagnostic clock. The ECM will record the following information when an event code is generated:
•The hour of the first occurrence of the code
•The hour of the last occurrence of the code
•The number of occurrences of the code
Logged events are listed in chronological order. The most recent event code is listed first.
This information can be helpful for troubleshooting intermittent problems. Logged codes can also be used to review the performance of the engine.
Clearing Event Codes
A code is cleared from memory when one of the following conditions occur:
•The code does not recur for 100 hours.
•A new code is logged and there are already ten codes in memory. In this case, the oldest code is cleared.
•The service technician manually clears the code.
Always clear logged event codes after investigating and correcting the problem which generated the code.
Troubleshooting
To troubleshoot the engine, perform the following steps to diagnose a malfunction:
1.Obtain the following information about the complaint:
oThe event and the time of the event
oDetermine the conditions for the event. The conditions will include the engine rpm and the load.
oDetermine if there are any systems that were installed by the dealer or by the customer that could cause the event.
oDetermine whether any additional events occurred.
2.Verify that the complaint is not due to normal engine operation. Verify that the complaint is not due to error of the operator.
3.Narrow the probable cause. Consider the operator information, the conditions of operation, and the history of the engine.
4.Perform a visual inspection. Inspect the following items:
oFuel supply
oOil level
oOil supply
oWiring
oConnectors
Be sure to check the connectors. This check is important for problems that are intermittent. Refer to Troubleshooting, "Electrical Connectors - Inspect" for additional information.
If these steps do not resolve the problem, refer to Table 1 for the procedure to troubleshoot the event code.
Parameter Settings of the Engine Monitoring System
The default settings for the parameters are programmed at the factory. The parameter settings for the engine monitoring system can also be viewed on Cat® Electronic Technician (ET).
Localización y solución de problemas de los síntomas
SMCS - 7569
Es posible que algunos síntomas del motor no estén relacionados con el sistema de control electrónico. Reúna la información sobre la queja que describe los síntomas. Verifique que la condición no se deba a la operación normal del motor.
Realice los siguientes pasos para determinar el problema.
Tabla 1
Pasos de prueba para la localización y solución de problemas |
Valores |
Resultados |
1. Repare todos los códigos activos.
|
Reparación
|
Resultado: no hay un código activo.
Continúe con el paso de prueba 2.
Resultado: hay un código activo.
Reparación: repare o reemplace cualquier material que sea necesario.
Si no se soluciona el problema, continúe con el Paso de prueba 2.
|
2. Reúna información del operador.
|
Información |
Continúe con el paso de prueba 3.
|
3. Verifique que el problema no se deba a la operación normal del motor.
|
Verifique |
Continúe con el paso de prueba 4.
|
4. Realice una inspección visual del motor.
A. Inspeccione los siguientes componentes:
- Cableado - Conectores - Nivel del combustible - Suministro de combustible - Nivel de aceite del motor - Suministro de aceite del motor - Nivel de refrigerante - Sistema de aire de admisión - Sistema de escape de aire
|
Inspeccionar |
Resultado: el motor está CORRECTO.
Continúe con el Paso de prueba 5.
Resultado: el motor NO ESTÁ CORRECTO.
Reparación: repare o reemplace cualquier material que sea necesario.
Si no se soluciona el problema, continúe con el Paso de prueba 5.
|
5. Inspección de los conectores eléctricos y el cableado
A. Inspeccione para ver si se presentan los siguientes problemas:
- Daños - Abrasión - Corrosión - Accesorio incorrecto
|
Inspeccionar |
Resultado: Los conectores y cables parecen estar en buenas condiciones.
Continúe con el paso de prueba 6.
Resultado: hay un problema en los conectores o el cableado.
Reparación: repare o reemplace los conectores o el mazo de cables. Asegúrese de que todos los sellos estén colocados correctamente y que los conectores estén acoplados.
Si no se soluciona el problema, continúe con el Paso de prueba 6.
|
6. Revise para ver si hay códigos registrados.
|
Códigos |
Resultado: no hay un código registrado.
Resultado: hay un código registrado.
- Determine si los códigos de diagnóstico registrados guardan relación con las causas probables. - Determine si los códigos de diagnóstico registrados ocurren al mismo tiempo que los síntomas. - Determine si los códigos de diagnóstico registrados se registran reiteradamente.
|
Si estas inspecciones no revelan ningún problema, utilice el procedimiento que mejor describa los síntomas.
